Number of found documents: 619
Published from to

Modifikace vlastností alkalicky aktivovaných aluminosilikátů polymerními přísadami
Mikhailova, Olesia; Bílek, Vlastimil; Vejmelková,, Eva; Žižková, Nikol; Rovnaník, Pavel
2023 - English
V současné době se v betonářském průmyslu ve velké míře používá portlandský cement (PC), jehož výroba má značný dopad na životní prostředí a zároveň se jedná o neudržitelný proces. Snahy o ekologičtější stavebnictví zahrnují využití několika aluminosilikátů, které mohou být buď odpadními produkty získanými z jiných průmyslových výrob, jako je granulovaná vysokopecní struska, popílek a křemičitá dýmka, nebo materiály pocházející z energeticky méně náročných průmyslových procesů, jako je metakaolin. Použití těchto materiálů při výrobě stavebních materiálů rovněž přispívá ke snížení výrobních nákladů. Aktivace aluminosilikátových materiálů alkalickými aktivátory vede k získání vysoce pevných materiálů, které lze považovat za alternativu běžného PC. Navzdory mnoha výhodám alkalicky aktivovaných aluminosilikátů (AAA) existuje zásadní nevýhoda, která se týká výrazného autogenního smršťování a smršťování při vysoušení, k němuž může docházet během tuhnutí materiálu. Tento jev vede k mikrotrhlinám a zhoršení mechanických lomových vlastností. Polymerní příměsi mohou modifikovat vlastnosti čerstvého a vytvrzeného materiálu AAA a překonat výše uvedené problémy. Tato disertační práce se zabývá vlivem polymerních přísad v různých hmotnostních množstvích aluminosilikátového pojiva na snižování smrštění a křehkosti a na zvýšení lomové houževnatosti. Jako polymerní příměsi byly vybrány polyetylen glykol (PEG), polypropylen glykol (PPG) a různé typy komerčních polymerů z řady dispergovatelných polymerních prášků Vinnapas®. Jejich vliv na vlastnosti získaných materiálů byl porovnáván s vlivem práškového přípravku proti smrštění Peramin SRA 40. Vzorky byly testovány na pevnost v ohybu a tlaku a jejich mikrostruktura byla zkoumána pomocí rtuťové porozimetrie a skenovací elektronové mikroskopie. Jedna z kapitol práce se zabývá studiem různých charakterizačních technik vzniku hlavních reakčních produktů v alkalicky aktivované strusce, jako jsou RTG difrakční analýza, Fourierovou tran Currently, the concrete industry utilizes Portland cement (PC) widely, whose production has a significant environmental impact, while it is also a non-sustainable process. Efforts towards a greener building industry involve employing several aluminosilicate materials that can be either by-products obtained from other industrial activities, such as granulated blast furnace slag, silica fume, and fly ash, or materials derived from less energy-intensive industrial processes, such as metakaolin. Using these materials in the preparation of building materials also contributes to reduced production costs. Activation of aluminosilicate materials by alkaline activators leads to high-strength materials that can be considered an alternative to ordinary Portland cement (OPC). Despite the numerous advantages of alkali-activated aluminosilicates (AAA), a major drawback is the significant autogenous and drying shrinkage that might occur during the material’s hardening. This phenomenon leads to microcracking and deterioration of mechanical fracture properties. Polymer admixtures can modify the properties of the fresh and hardened AAA material and overcome the abovementioned problems. This thesis investigates the influence of polymer admixtures, in different amounts by weight of the aluminosilicate binder, on reducing shrinkage and fragility and increasing fracture toughness. Polyethylene glycol (PEG), Polypropylene glycol (PPG), and different types of commercial polymers of the Vinnapas® - family of dispersible polymer powders were selected as polymer admixtures. Their effect on the properties of the obtained materials was compared with that of powder shrinkage reducer Peramin SRA 40. The specimens were tested for flexural and compressive strength, and their microstructure was investigated employing mercury intrusion porosimetry and scanning electron microscopy One of the chapters of the thesis deals with the study of different analytical techniques for the characterization Keywords: Alkali activated materials; geopolymers; slag; metakaolin; polymer admixtures; Alkalicky aktivované materiály; geopolymery; struska; metakaolin; polymerní přísady Available in a digital repository NRGL
Modifikace vlastností alkalicky aktivovaných aluminosilikátů polymerními přísadami

V současné době se v betonářském průmyslu ve velké míře používá portlandský cement (PC), jehož výroba má značný dopad na životní prostředí a zároveň se jedná o neudržitelný proces. Snahy o ...

Mikhailova, Olesia; Bílek, Vlastimil; Vejmelková,, Eva; Žižková, Nikol; Rovnaník, Pavel
Vysoké učení technické v Brně, 2023

Field Programmable Neural Networks odolná proti poruchám
Krčma, Martin; Kordík, Pavel; Stopjaková, Viera; Drábek, Vladimír
2023 - English
Tato práce se zaměřuje na koncept Field Programmable Neural Networks jehož cílem je učinit implementaci umělých neuronových sítí v hradlových polích méně náročnou jejich prostředky. Za tímto účelem práce koncept rozvíjí a představuje několik jeho různých typů jež se vyznačují různými poměry mezi spotřebou zdrojů hradlových polí a přesností s jakou aproximují původní neuronovou síť jíž implementují. Teze díle rozšiřuje koncept o metody zabezpečení proti poruchám s využitím redundance a také bez ní. This thesis focuses on the Field Programmable Neural Networks concept intended to make implementation of neural networks in FPGAs less resource demanding. The thesis introduces and discusses several types of Field Programmable Neural Networks which provide different trad-offs between the resource consumption and the accuracy of the implemented neural network approximation. This thesis also introduces and discusses methods of hardening the Field Programmable Neural Networks against faults with and without redundancy. Keywords: Field Programmable Neural Networks; fault tolerance; neural networks; FPGAs; Field Programmable Neural Networks; odolnost proti poruchám; neuronové sítě; FPGA Available in a digital repository NRGL
Field Programmable Neural Networks odolná proti poruchám

Tato práce se zaměřuje na koncept Field Programmable Neural Networks jehož cílem je učinit implementaci umělých neuronových sítí v hradlových polích méně náročnou jejich prostředky. Za tímto účelem ...

Krčma, Martin; Kordík, Pavel; Stopjaková, Viera; Drábek, Vladimír
Vysoké učení technické v Brně, 2023

Experimental investigation and numerical modelling of top of rail products
Kvarda, Daniel; prof.Roger Lewis; Meierhofer, Alexander; Hartl, Martin
2023 - English
Tato disertační práce se zabývá experimentálním a numerickým studiem maziv pro temeno kolejnice. Tyto maziva se používají ke snížení opotřebení, hluku a zlepšení energetické účinnosti kontaktu kola a kolejnice. V posledních dvou desetiletích byl proveden rozsáhlý experimentální výzkum týkající se použití maziv pro temeno kolejnice. Avšak velmi málo výzkumu bylo zaměřeno na základní mechanismy těchto produktů, zejména na problémy s nízkou adhezí. Aplikace matematických modelů v této oblasti také nebyla dosud zkoumána. Cílem této práce je pomocí matematického modelu vysvětlit třecí chování a problémy s nízkou adhezí maziv pro temeno kolejnice. Model předpokládá jak tření vznikající interakcí nerovností pevných látek, tak separaci mazacím filmem. Validace tohoto modelu byla provedena na experimentálním tribometru se schopností měřit tloušťku filmu pro ověření přesné predikce separace povrchu. Komerční tribometr byl použit ke zkoumání vlivu jednotlivých složek v mazivu pro temeno kolejnice na bázi oleje. Sada reologických testů v kombinaci s modelem ukázala, že pevné částice měly velmi malý vliv na zvýšení adheze po aplikaci. Následně byly testovány různé typy maziv pro temeno kolejnice pomocí vysokotlakého torzního zařízení. Mezný režim tření těchto látek byl hodnocen představeným modelem. Bylo zjištěno, že pozitivní třecí vlastnosti, které by tyto produkty měly poskytovat, jsou výsledkem velké skluzové vzdálenosti, která mění složení třecí vrstvy. Nízký koeficient tření v důsledku nadměrné aplikace se vyskytl při stejném aplikovaném množství u všech testovaných látek. Tato diplomová práce představuje původní výzkum rozšiřující znalosti o produktech pro temeno kolejnice. This dissertation thesis deals with experimental and numerical study of top or rail products. These products are used to reduce wear, noise and improve energy efficiency of wheel and rail contact. In the last two decades, extensive experimental research has been conducted on the use of top of rail products. However, very little research has focused on the fundamental mechanisms of these products, especially causes of low adhesion. Application of mathematical models to this field was also not yet examined. The aim of this thesis is to explain the frictional behaviour and low adhesion conditions of the top of rail products with the use of a mathematical model. The model assumes both friction arising from solid asperity interaction and separation by a fluid film. The validation of this model was carried out on an experimental tribometer with the ability to measure film thickness to validate the accurate prediction of surface separation. A commercial tribometer was used to investigate the influence of individual components in oil-based top of rail product on the coefficient of adhesion. A set of rheological tests in combination with the model showed that the solid particles had very little effect in increasing adhesion after application. Subsequently, different types of top of rail products were tested using a high pressure torsion device. The boundary friction of these substances was evaluated by the model. The positive frictional characteristics that these products should provide are found to be a result of sliding friction changing the composition of the interfacial layer. In addition, the low coefficient of friction due to overapplication occurred at the same amount applied for all tested substances. This thesis presents original research expanding on the knowledge of top of rail products. Keywords: Wheel-rail contact; Friction management; Top of rail products; Numerical model; Tribology; Kontakt kolo-kolejnice; Řízení tření; Maziva pro kolejový svršek; Numerický model; Tribologie Available in a digital repository NRGL
Experimental investigation and numerical modelling of top of rail products

Tato disertační práce se zabývá experimentálním a numerickým studiem maziv pro temeno kolejnice. Tyto maziva se používají ke snížení opotřebení, hluku a zlepšení energetické účinnosti kontaktu kola a ...

Kvarda, Daniel; prof.Roger Lewis; Meierhofer, Alexander; Hartl, Martin
Vysoké učení technické v Brně, 2023

Mechanismy poškození niklové superslitiny René 41 při únavě
Babinský, Tomáš; Pippan, Reinhard; Růžička,, Milan; Polák, Jaroslav
2023 - English
Předkládaná práce se zabývá vznikem poškození ve tvářené niklové superslitině René 41, která je podrobena únavovému zatěžování za pokojové a zvýšené (800 °C) teploty. Slitina byla zkoumána ve dvou termodynamických stavech: po rozpouštěcím žíhání a po stárnutí. Jednoosé zkoušky nízkocyklové únavy byly prováděny symetricky vzhledem k řízené veličině, kterou byla celková podélná deformace. Za účelem studia mechanismů poškození a jejich souvislosti s plastickou deformací byly aplikovány techniky elektronové mikroskopie doplněné o analýzu cyklické odezvy ve formě hysterezních smyček statistickým přístupem. Navíc byly provedeny přerušované únavové zkoušky za účelem studia vývoje povrchového reliéfu ve vztahu k dislokační substruktuře, k čemuž bylo opět využito elektronové mikroskopie. Porušení za pokojové teploty bylo povětšinou transkrystalické, únavové trhliny iniciovaly především uvnitř zrn z povrchového reliéfu. Srovnáme-li dva zkoušené stavy, stárnutý materiál vykazoval vyšší hodnoty cyklického napětí a při srovnatelném napětí dosahoval vyšších životností. Cyklická deformace byla od prvního cyklu lokalizována do persistentních skluzových pásů. Bylo zjištěno, že většina skluzových pásů vzniká na začátku únavového života, kvůli čemuž jsou koherentní precipitáty ‘ významně deformovány pouze na začátku únavového života. Skluz v persistentních skluzových pásech vedl k vytvoření povrchového reliéfu ve formě skluzových schodů, extruzí a intruzí. Vznik povrchového reliéfu byl podrobně diskutován s existujícími modely. Vysokoteplotní expozice měla za následek oxidaci povrchu, zejména na oslabených hranicích zrn, kde iniciovaly a následně se šířily únavové trhliny. Výsledné poškození bylo tudíž interkrystalické. The present study deals with the aspects of fatigue damage in a wrought Ni-based superalloy René 41. The material of interest was investigated in two thermodynamical states: solutionised and aged. Uniaxial, fully-reversed low-cycle fatigue tests were conducted at room and elevated (800 °C) temperatures under total strain amplitude control. To study the relevant damage mechanisms and reveal their connection to plastic deformation, a detailed analysis of the cyclic response using a statistical approach was performed, and advanced microscopy techniques were employed, namely scanning and transmission electron microscopy. Interrupted fatigue tests were performed to study the evolution of surface relief and the underlying dislocation structure. After each interruption, the evolution of the microstructure was analysed using electron microscopy techniques. At room temperature, the damage was mostly transgranular, and the cracks initiated predominantly within grains from the roughened surface. Comparing the two investigated material states, the aged material attained higher stresses and exhibited higher lifetimes in service-relevant stress-life relation. Cyclic deformation was found to localize to persistent slip bands since the first cycle, and the majority of slip bands formed very early in the fatigue life. Hence, shearing of the strengthening phase, coherent ’ precipitates, occurred largely only in the first few cycles. Due to the cyclic slip localization, surface roughening emanated in the form of slip steps, extrusions and intrusions. The formation of surface relief was thoroughly discussed with existing models. The exposure to high temperatures led to an environmental attack, due to which an oxide layer formed on the surface. The cracks initiated and propagated along weakened grain boundaries, and the resulting damage was thus intergranular. Keywords: Low-cycle fatigue; Cyclic slip localization; Persistent slip band (PSB); Persistent slip marking (PSM); Dislocation; Electron microscopy; Superalloy; Nízkocyklová únava; Lokalizace cyklické deformace; Persistentní skluzový pás; Persistentní skluzová stopa; Dislokace; Elektronová mikroskopie; Superslitina Available in a digital repository NRGL
Mechanismy poškození niklové superslitiny René 41 při únavě

Předkládaná práce se zabývá vznikem poškození ve tvářené niklové superslitině René 41, která je podrobena únavovému zatěžování za pokojové a zvýšené (800 °C) teploty. Slitina byla zkoumána ve dvou ...

Babinský, Tomáš; Pippan, Reinhard; Růžička,, Milan; Polák, Jaroslav
Vysoké učení technické v Brně, 2023

Measurement of Shape and Dimensions of Forgings
Hurník, Jakub; Bračun, Drago; Piano, Samanta; Koutný, Daniel
2023 - English
V procesu výroby těžkých výkovků volným kováním vznikají nepřesnosti, které je třeba měřit a korigovat. Metoda pasivního měření výkovků, na základě jejich siluet v obraze, zde potenciálně nabízí mnoho výhod. V případě měření výkovků ale v literatuře vykazuje relativně nízkou přesnost a nebyla ověřena v průmyslových podmínkách. Cílem práce je proto prozkoumat možnosti využití této metody v reálných podmínkách, které umožní pokročilé metody optického měření. Jsou diskutovány rušivé vlivy prostředí a navrhovány originální metody, jak ovlivnění zmírnit nebo mu předejít. Ty jsou ověřovány v laboratorním i v průmyslovém prostředí. Výsledky potvrzují efektivitu navržených metod; dosahovaná přesnost je stejného řádu s tou dosaženou v laboratorním prostředí. Bylo dosaženo chyby okolo 1 mm v měřicím objemu 6 × 6 × 2 m v případě měření přímosti osy a průměru výkovku. Tento výsledek postačuje požadavkům průmyslového prostředí. Nicméně, měření stále obsahuje odlehlé hodnoty, jejichž výskyt je diskutován. Poznatky obsažené v této práci je možné využít při vývoji profesionálního měřicího systému pro tuto aplikaci. Sekundárně jsou pak zobecnitelné a využitelné při měření horkých objektů nebo obecně objektů v komplexním prostředí na základě jejich siluet. Systém pro měření výkovků by v budoucnu mohl přinést vyšší efektivitu výroby volně kovaných polotovarů a mohl by se stát součástí automatizované kovací linky. In the process of open-die forging, inaccuracies can appear. These inaccuracies must be measured and corrected. Passive heavy forging measurement, based on their silhouettes in images, potentially offers many advantages in this application. However, regarding forging measurement, this method showed limited accuracy in the literature and was never verified under industrial conditions. Therefore, the aim of this thesis is to examine the feasibility of this method in the industrial environment, by using advanced methods of optical measurement. Interfering effects are discussed, and original methods, working as countermeasures, are proposed. Methods are verified in both the laboratory and the industrial environment. The results suggest the effectiveness of the proposed methods; the accuracy achieved in the laboratory and industrial environment is of the same order. The error is approximately around 1 mm in a measurement volume of 6 × 6 × 2 m for the geometry of the axis and the measurement of the diameter. This result satisfies the demands of an industrial environment. However, the measurement still contains outliers, which are discussed. The knowledge obtained can be used during the development of a professional measurement system for this application. Secondly, the knowledge can be generalized to the measurement of hot objects, or objects in a complex environment, based on their silhouettes. A system for the measurement of forgings could increase the effectiveness of manufacturing and could become a part of automated forging production line in the future. Keywords: forging; measurement; silhouettes; edge detection; axis straightness; výkovek; měření; siluety; detekce hran; přímost osy Available in a digital repository NRGL
Measurement of Shape and Dimensions of Forgings

V procesu výroby těžkých výkovků volným kováním vznikají nepřesnosti, které je třeba měřit a korigovat. Metoda pasivního měření výkovků, na základě jejich siluet v obraze, zde potenciálně nabízí mnoho ...

Hurník, Jakub; Bračun, Drago; Piano, Samanta; Koutný, Daniel
Vysoké učení technické v Brně, 2023

Využití fluorescenčních technik k analýze průmyslově významných mikroorganismů
Müllerová, Lucie; Kráčmar, Stanislav; Krčma, František; Obruča, Stanislav
2023 - English
Techniky analýzy jednotlivých buněk neboli single-cell analýzy, jsou velmi důležité v kontextu studia důležitých biotechnologických mikroorganismů. V biotechnologických procesech je optimální mít rychlé, efektivní a real-time analýzy, které lze provést s minimální přípravou vzorku. Proto jsme v rámci předložené disertační práce využili autofluorescenci jako marker fyziologického stavu mikrobiální kultury, který je možné analyzovat pomocí fluorescenční mikroskopie a/nebo průtokové cytometrie. Nejdříve bylo potvrzeno, na základně emisních spekter, že zelená autofluorescence emitovaná bakteriemi Cupriavidus necator H16 a jejím polyhydroxyalkanoáty (PHA) neprodukujícím mutantem Cupriavidus necator PHB-4, pochází skutečně z flavinů. Emisní maximum bylo naměřeno v rozmezí 510–550 nm pro FAD, FMN a riboflavin – bohužel jednotlivá spektra od sebe nebylo možné rozeznat, a 515 nm pro oba bakteriální kmeny Cupriavidus necator. Byly nalezeny dvě maxima excitačních spekter, jedno v rozmezí 360–370 nm a druhé okolo 440 nm. Z těchto poznatků byl sestaven nový protokol pro fluorescenční mikroskopii – laser byl nastaven na hodnotu 467 nm a emisní filtr pro detekci byl vybrán 520/35 nm. Flaviny a jejich autofluorescence může být take použita v kombinaci s jinými fluorofory, když jsou použity multiparametrické analýzy, ale je důrazně doporučeno, aby vybrané fluorescenční sondy buď emitovaly v jiném rozmezí, než je 500–550 nm anebo byla jejich doba života excitovaného stavu jiná, než je interval 3,2–3,7 a 4,2 – 4,9 ns. Tyto doby života navíc zůstaly konstantní, i když byly buňky vystaveny kultivačním a stresovým podmínkám. To z nich dělá velmi stabilní marker v porovnání s dynamickým charakterem intenzit fluorescence. Dále byl optimalizován protokol pro značení bakterie C. necator s využitím PHA specifické sondy BODIPY 493/503. Optimální koncentrace této lipofilní sondy byla stanovena na 2,5 µg ml-1 a sondu je možné dle našich dat aplikovat společně s viabilitní sondou propidium iodidem. Tento protokol byl také využit pro studium morfologie PHA-syntetizující halofilní bakterie Halomonas halophila. Pro stanovení UV-protektivních vlastností PHA obsaženého v bakterii Cupriavidus necator, byl optimalizován další protokol, tentokrát pro ROS citlivou sondu CM-H2DCFDA, která byla stanovená jako citlivější v porovnání s její nemethylovanou formou. V této studii byly navíc potvrzeny UV-protektivní vlastnosti PHA na bakterii Cupriavidus necator H16 v porovnání s PHA nesyntetizujícím kmenem Cupriavidus necator PHB-4. Single-cell analysis techniques are very important when studying relevant biotechnological microorganisms. In biotechnological processes, the optimum is to have fast, efficient and real-time analyses that can be done with minimal preparations. Therefore, we looked at autofluorescence as a possible and natural marker when employing fluorescence microscopy and flow cytometry. First, it has been established, based on the emission spectra, that the green autofluorescence of the bacteria used – Cupriavidus necator H16 and its non polyhydroxyalkanoates (PHA) producing mutant Cupriavidus necator PHB-4, is caused predominantly by flavins. The maxima of emission spectra were 510 – 550 nm for FAD, FMN and riboflavin whose spectra could not be distinguished, and 515 nm for both strains of Cupriavidus necator. Two maxima of excitation spectra of the bacteria were found – one in the range 360 – 370 nm and another around 440 nm, and so a new protocol for fluorescence microscopy has been established - the laser used was 467 nm and the emission filter chosen for the detection was 520/35 nm. Flavins and their autofluorescence can also be used in combination with other fluorophores when the need for multi-parametrical analyses arises, but it’s highly recommended the other dyes emit other than green fluorescence in the band of 500 – 550 nm or/and have an average fluorescence lifetime other than 3.2 – 3.7 and 4.2 - 4.9 ns. These values stayed constant even when the cells were exposed to various cultivation and even stress conditions. That makes them a very stable marker compared to the dynamic marker of fluorescence intensity that changes immediately after a change in the environment. A new staining protocol for C. necator using PHA-specific hydrophobic probe BODIPY 493/503 was optimised. The optimal staining concentration of the lipophilic dye BODIPY 493/503 was determined to be 2.5 µg ml-1 and it can be used in combination with propidium iodide. The BODIPY 493/503 staining protocol has been used when analysing the morphology of the PHA-synthesising bacteria Halomonas halophila. Further, to study the UV-protective properties of PHA in Cupriavidus necator, another staining essay has been optimised. It has been established that the ROS sensitive dye CM-H2DCFDA gives better performance than its non-methylated form. Also, the UV-protective characteristics of the PHA-synthesising strain Cupriavidus necator H16 were confirmed when compared to its non-PHA synthesising strain C. necator PHB-4. Keywords: Bacterial autofluorescence; Cupriavidus necator; Sporomusa ovata; Halomonas halophila; single cell analysis; average fluorescence lifetime; oxidative stress; ROS; biotechnological processes quality control; PHB protective characteristics; flow cytometry; fluorescence microscopy; fluorescence stain optimisation; Bakteriální autofluorescence; Cupriavidus necator; Sporomusa ovata; Halomonas halophila; analýzy jedné buňky; doba života excitovaného stavu; oxidativní stress; ROS; kvalita kontroly biotechnologických procesů; protektivní charakteristiky PHB; průtoková cytometrie; fluorescenční mikroskopie; optimalizace fluorescenčního barvení Available in a digital repository NRGL
Využití fluorescenčních technik k analýze průmyslově významných mikroorganismů

Techniky analýzy jednotlivých buněk neboli single-cell analýzy, jsou velmi důležité v kontextu studia důležitých biotechnologických mikroorganismů. V biotechnologických procesech je optimální mít ...

Müllerová, Lucie; Kráčmar, Stanislav; Krčma, František; Obruča, Stanislav
Vysoké učení technické v Brně, 2023

Stanovení mechanických vlastností tenkých filmů pomocí numerického modelování experimentálních testů
Tinoco Navarro, Hector Andres; Jančo,, Roland; Klusák,, Jan; Hutař, Pavel
2023 - English
Testování tenkých filmů pomocí "Bulge testu" je experimentální technika která zahrnuje použití numerických a analytických přístupů k charakterizaci mechanických vlastností tenkých vrstev. Tato práce se zabývá některými omezeními nalezenými v klasických modelech, které popisují chování tenkých vrstev podrobených tomuto testu. Za tímto účelem byly vyvinuty nové modely a numerické strategie pro stanovení různých mechanických vlastností jednovrstvých a dvouvrstvých tenkých vrstev za odlišných strukturních podmínek, jako je elasticita, plasticita a lom. Kombinací metody konečných prvků a klasických analytických řešení byly navrženy a ověřeny různé metodiky pro výpočet elastických vlastností (E a v), zbytkových napětí, meze kluzu a lomové houževnatosti. Mechanické vlastnosti filmů z nitridu křemíku, hliníku a zlata byly charakterizovány pomocí experimentálních dat o zatížení-průhybu získaných z měření. Stanovené vlastnosti vykazovaly uspokojivou shodu s což potvrdilo, že metody navržené v této práci mohou být užitečné pro odhad mechanických vlastností se známými materiálovými vlastnostmi tenkých vrstev. Bulge testing is an experimental technique that involves the use of numerical and analytical approaches to characterize the mechanical properties of thin films. This thesis addresses some limitations found in the classical models that describe the behavior of thin films subjected to this test. This required the development of new models and numerical strategies in order to determine several mechanical properties of monolayer and bilayer thin films under different structural conditions, such as elasticity, plasticity, and fracture. By combining finite element analysis and classical analytical solutions, different methodologies for calculating the elastic properties (E and v), residual stresses, yield stress, and fracture toughness were proposed and validated. The mechanical properties of silicon nitride, aluminum, and gold films were characterized using load-deflection experimental data obtained from bulging measurements. The determined properties showed reasonable agreement with materials of known properties, which validated that the proposed methods in this work can be useful for estimating the mechanical properties of freestanding thin films. Keywords: Bulge test; thin film; finite element analysis; load-deflection; elastic properties; yield stress; fracture toughness; Bulge; tenký film; analýza metodou konečných prvků; elastické vlastnosti; mez kluzu; Lomová houževnatost Available in a digital repository NRGL
Stanovení mechanických vlastností tenkých filmů pomocí numerického modelování experimentálních testů

Testování tenkých filmů pomocí "Bulge testu" je experimentální technika která zahrnuje použití numerických a analytických přístupů k charakterizaci mechanických vlastností tenkých vrstev. Tato práce ...

Tinoco Navarro, Hector Andres; Jančo,, Roland; Klusák,, Jan; Hutař, Pavel
Vysoké učení technické v Brně, 2023

Processing of metallic materials by Selective Laser Melting at elevated temperatures
Malý, Martin; Filho, Sergio de Traglia Amancio; Dr. Michael R. Tucker; Koutný, Daniel
2023 - English
Tato disertační práce se zabývá vlivem předehřevu na výrobu komponent 3D tiskem kovů technologií Selective Laser Melting (SLM), také známou pod označením Laser Powder Bed Fusion (LPBF). V práci je obsažen přehled současného stavu poznání v oblasti realizace předehřevu a fyzikální podstaty předehřevu. Dále je v práci obsažen přehled vlivu předehřevu na konkrétní typy materiálů. Mezi tyto typy materiálů byly zařazeny titanové, intermetalické, niklové a hliníkové slitiny a měď. Z rešeršní části byly identifikovány perspektivní oblasti, které doposud nebyly dostatečně zkoumány, a kde by předehřev mohl vést k zefektivnění technologie LPBF a rozšíření oblasti zpracovatelných materiálů. Mezi tyto oblasti bylo zařazeno zkoumání vlivu předehřevu v kombinaci s dalšími procesními parametry na zbytková napětí u slitiny Ti6Al4V, vliv předehřevu na niklovou slitinu Inconel 939 a na měď. Předpokladem u Ti6Al4V a Inconelu 939 bylo, že předehřev sníží zbytková napětí a bude tak možné snížit množství podpůrných struktur během výroby, což by vedlo k zefektivnění technologie. Tato hypotéza byla zamítnuta, protože i přes snížení zbytkových napětí u Ti6Al4V nedošlo k jejich eliminaci a navíc, došlo k rychlé degradaci nepoužitého prášku, což zvyšuje náklady na výrobu. U Inconelu 939 dokonce zvýšená teplota vedla k vyšším deformacím, a tedy zbytkovým napětím v důsledku evoluce karbidické fáze. Další perspektivní oblastí, kde by předehřev mohl vést k zvýšení portfolia zpracovatelných materiálů, je měď. Měď je díky vysoké tepelné vodivosti a odrazivosti laserového záření považována za obtížně zpracovatelnou technologií LPBF. Z experimentů byl potvrzen velice pozitivní vliv předehřevu na relativní hustotu vzorků. Vzorky dosáhly hodnot relativní hustoty přes 99 % pokud byly tisknuty s předehřevem 400 °C. Bylo tedy experimentálně ověřeno, že předehřev může významně zlepšit zpracovatelnost skupiny materiálů, které mají nízkou pohltivost laserového záření a materiálů s vysokou teplenou vodivostí. Všechny výsledky vedou k lepšímu pochopení chování materiálů během zpracování technologií LPBF a mohou vést k jejímu rozšíření do dalších průmyslových odvětví. Výsledky jsou shrnuty ve třech publikacích, které byly vydány ve vědeckých časopisech. This dissertation thesis deals with the influence of preheating on the components produced using Selective Laser Melting (SLM), also known as Laser Powder Bed Fusion (LPBF) technology. The thesis contains an overview of the current state of knowledge in the field of preheating and the physical nature of preheating. Furthermore, the work contains an overview of the effect of preheating on specific types of materials. These types of materials included in the state of the art are titanium, intermetallic, nickel and aluminium alloys, and copper. From the state of knowledge, promising research areas were identified, where preheating could lead to more efficient production using LPBF technology and to expansion of the area of processable materials. These areas include the investigation of the effect of preheating in combination with other process parameters on the residual stresses of Ti6Al4V alloy, the effect of preheating on nickel alloy Inconel 939 and copper. The premise of the Ti6Al4V and Inconel 939 topics was that preheating would reduce residual stresses, and thus will be possible to reduce the necessary amount of support structures. The results can lead to more cost-effective production using LPBF technology. This hypothesis was rejected. Despite the reduction in residual stresses in Ti6Al4V, they were not fully eliminated and, in addition, a rapid degradation of unused powder was detected, which increases production costs. The preheating of the Inconel 939, against the assumption based on behaviour of other materials, led to higher deformations and thus residual stresses, due to the evolution of precipitates. Another selected area where preheating could lead to an increase in the portfolio of processable materials is the processing of copper. Copper is a difficult to process material using LPBF technology due to its high thermal conductivity and laser reflectivity. The experiments confirmed a very positive effect of preheating on the relative density of the samples. The samples reached relative density values of over 99% when fabricated with preheating at 400 °C. Thus, preheating can significantly improve the process ability of reflective and high conductive materials. All of the results lead to a better understanding of the behaviour of the materials during processing by LPBF technology and may lead to its further expansion to more industries. The results are summarized in three publications that have been published in scientific journals. Keywords: Laser powder bed fusion; Selective laser melting; residual stress; preheating; Ti6Al4V; Inconel; copper; Laser powder bed fusion; Selective laser melting; zbytková napětí; předehřev; Ti6Al4V; Inconel; měď Available in a digital repository NRGL
Processing of metallic materials by Selective Laser Melting at elevated temperatures

Tato disertační práce se zabývá vlivem předehřevu na výrobu komponent 3D tiskem kovů technologií Selective Laser Melting (SLM), také známou pod označením Laser Powder Bed Fusion (LPBF). V práci je ...

Malý, Martin; Filho, Sergio de Traglia Amancio; Dr. Michael R. Tucker; Koutný, Daniel
Vysoké učení technické v Brně, 2023

Field Programmable Neural Networks odolná proti poruchám
Krčma, Martin; Kordík, Pavel; Stopjaková, Viera; Drábek, Vladimír
2023 - English
Tato práce se zaměřuje na koncept Field Programmable Neural Networks jehož cílem je učinit implementaci umělých neuronových sítí v hradlových polích méně náročnou jejich prostředky. Za tímto účelem práce koncept rozvíjí a představuje několik jeho různých typů jež se vyznačují různými poměry mezi spotřebou zdrojů hradlových polí a přesností s jakou aproximují původní neuronovou síť jíž implementují. Teze díle rozšiřuje koncept o metody zabezpečení proti poruchám s využitím redundance a také bez ní. This thesis focuses on the Field Programmable Neural Networks concept intended to make implementation of neural networks in FPGAs less resource demanding. The thesis introduces and discusses several types of Field Programmable Neural Networks which provide different trad-offs between the resource consumption and the accuracy of the implemented neural network approximation. This thesis also introduces and discusses methods of hardening the Field Programmable Neural Networks against faults with and without redundancy. Keywords: Field Programmable Neural Networks; fault tolerance; neural networks; FPGAs; Field Programmable Neural Networks; odolnost proti poruchám; neuronové sítě; FPGA Available in a digital repository NRGL
Field Programmable Neural Networks odolná proti poruchám

Tato práce se zaměřuje na koncept Field Programmable Neural Networks jehož cílem je učinit implementaci umělých neuronových sítí v hradlových polích méně náročnou jejich prostředky. Za tímto účelem ...

Krčma, Martin; Kordík, Pavel; Stopjaková, Viera; Drábek, Vladimír
Vysoké učení technické v Brně, 2023

Access and Backhaul Solutions for Cellular-Enabled Industrial Wearables
Saafi, Salwa; Bečvář, Zdeněk; Tölli, Antti; Hošek, Jiří
2023 - English
Smartphones are no longer the only portable devices changing the lives and daily routines of today’s digitally connected consumers. Smart glasses, watches, headsets, cameras, bands, trackers, monitors, and scanners are all examples of hands-free inherently mobile wearable devices that enable the emerging consumer and industrial applications. Similarly to customers who are ready to embrace life-changing experiences with new devices, companies and industries are also employing smart helpers and intelligent assistant systems to improve the efficiency of their automated processes and the productivity and safety of their workers. Not limited to the employment of smart helpers, the industrial digital transformation relies heavily on the deployment of communication infrastructures that utilize efficient cellular technologies to meet the dissimilar requirements of industrial applications. Motivated by these intelligent assistant systems and communication technologies, this dissertation focuses on the role of wearable technology and cellular connectivity in enabling the automation of vertical domains. Aiming to address the current technology gap behind cellular-enabled industrial wearables, the present work is dedicated to assessing the applicability of cellular connectivity to industrial wearables and developing efficient access and backhaul solutions for the support of the requirements of emerging industrial applications. The following outline of this dissertation is built around the main objectives as highlighted above and presents the main outcomes of this work, which include (i) a concise technology review capturing the evolution of the recent solutions proposed by the 3rd Generation Partnership Project (3GPP) for wearable devices and communications, (ii) an introduction to novel categories of industrial wearable applications with mid-end requirements that fall in-between the two extremes of high-end and low-end Fifth-Generation (5G) service classes, (iii) an assessment of the applicability of the emerging Reduced-Capability New Radio (NR RedCap) technology to the newly introduced wearable applications, (iv) an extension of the RedCap wearable communications with Device-to-Device (D2D) and Supplementary Uplink (SUL) capabilities for enhanced access network performance, (v) a cost-efficient backhaul selection solution based on Markov Decision Processes (MDPs) for time-sensitive wearable applications in an integrated terrestrial and non-terrestrial communication scenario, and (vi) a data-driven Artificial Intelligence (AI)-aided approach for the management of complex industrial networks with dissimilar device capabilities, communication solutions, and application requirements. A set of simulation and analytical models is developed to assess the relevant key performance indicators as part of the above contributions. Beyond indicating the need for technology improvement demanded by the efficient integration of wearable devices into cellular networks and the satisfaction of industrial application requirements, the numerical results reported in this dissertation confirm the network performance enhancements achieved by the access and backhaul solutions contributed in this work. Smartphones are no longer the only portable devices changing the lives and daily routines of today’s digitally connected consumers. Smart glasses, watches, headsets, cameras, bands, trackers, monitors, and scanners are all examples of hands-free inherently mobile wearable devices that enable the emerging consumer and industrial applications. Similarly to customers who are ready to embrace life-changing experiences with new devices, companies and industries are also employing smart helpers and intelligent assistant systems to improve the efficiency of their automated processes and the productivity and safety of their workers. Not limited to the employment of smart helpers, the industrial digital transformation relies heavily on the deployment of communication infrastructures that utilize efficient cellular technologies to meet the dissimilar requirements of industrial applications. Motivated by these intelligent assistant systems and communication technologies, this dissertation focuses on the role of wearable technology and cellular connectivity in enabling the automation of vertical domains. Aiming to address the current technology gap behind cellular-enabled industrial wearables, the present work is dedicated to assessing the applicability of cellular connectivity to industrial wearables and developing efficient access and backhaul solutions for the support of the requirements of emerging industrial applications. The following outline of this dissertation is built around the main objectives as highlighted above and presents the main outcomes of this work, which include (i) a concise technology review capturing the evolution of the recent solutions proposed by the 3rd Generation Partnership Project (3GPP) for wearable devices and communications, (ii) an introduction to novel categories of industrial wearable applications with mid-end requirements that fall in-between the two extremes of high-end and low-end Fifth-Generation (5G) service classes, (iii) an assessment of the applicability of the emerging Reduced-Capability New Radio (NR RedCap) technology to the newly introduced wearable applications, (iv) an extension of the RedCap wearable communications with Device-to-Device (D2D) and Supplementary Uplink (SUL) capabilities for enhanced access network performance, (v) a cost-efficient backhaul selection solution based on Markov Decision Processes (MDPs) for time-sensitive wearable applications in an integrated terrestrial and non-terrestrial communication scenario, and (vi) a data-driven Artificial Intelligence (AI)-aided approach for the management of complex industrial networks with dissimilar device capabilities, communication solutions, and application requirements. A set of simulation and analytical models is developed to assess the relevant key performance indicators as part of the above contributions. Beyond indicating the need for technology improvement demanded by the efficient integration of wearable devices into cellular networks and the satisfaction of industrial application requirements, the numerical results reported in this dissertation confirm the network performance enhancements achieved by the access and backhaul solutions contributed in this work. Keywords: Wearables; cellular connectivity; industrial networks; 5G and beyond; NR RedCap; access solutions; D2D; SUL; backhaul selection; MDP; AI.; Wearables; cellular connectivity; industrial networks; 5G and beyond; NR RedCap; access solutions; D2D; SUL; backhaul selection; MDP; AI. Available in a digital repository NRGL
Access and Backhaul Solutions for Cellular-Enabled Industrial Wearables

Smartphones are no longer the only portable devices changing the lives and daily routines of today’s digitally connected consumers. Smart glasses, watches, headsets, cameras, bands, trackers, ...

Saafi, Salwa; Bečvář, Zdeněk; Tölli, Antti; Hošek, Jiří
Vysoké učení technické v Brně, 2023

About project

NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web

Send your suggestions and comments to nusl@techlib.cz

Provider

http://www.techlib.cz

Facebook

Other bases