METIS – Design report - mirrors
Lédl, Vít; Melich, Radek; Psota, Pavel; Steiger, Lukáš; Vít, Tomáš; Kovačičinová, Jana
2013 - anglický
The presented study shows results from the mechanical design of M1 and M2 mirrors for METIS/ICOR. The study compares the material properties of different materials, which are often used for manufacturing of
Klíčová slova:
METIS; lightweighted mirrors; low microroughness
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
METIS – Design report - mirrors
The presented study shows results from the mechanical design of M1 and M2 mirrors for METIS/ICOR. The study compares the material properties of different materials, which are often used for ...
Illumination study of 3SU1 project
Melich, Radek; Vojtíšek, Petr; Mach, M.
2013 - anglický
This document provides report of results obtained during measurement of Siemens 3SU1 PLCompact, 3SU1 PLModular nad PCB indicators and their comparison to 3SB3 and Allan Bradley pilot lights.
Klíčová slova:
angular radiation measurement
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Illumination study of 3SU1 project
This document provides report of results obtained during measurement of Siemens 3SU1 PLCompact, 3SU1 PLModular nad PCB indicators and their comparison to 3SB3 and Allan Bradley pilot lights.
Měřicí systém pro měření svěšování vřetene obráběcích strojů
Pintr, Pavel; Václavík, Jan
2013 - český
Zařízení slouží k měření ohybu těžkého vřetene při výsuvu z vřeteníku. Použita je metoda měření sklonu s imitovanou závislostí na deformaci nosiče měřené soustavy Device serves as a diagnostic tool for analysis and measurement of spindle bending during extension from its headstock. A method used to measure the bending has minimized sensitivity to deformation of supporting structures.
Klíčová slova:
heavy spindle; bending; measurement; deflection; laser
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Měřicí systém pro měření svěšování vřetene obráběcích strojů
Zařízení slouží k měření ohybu těžkého vřetene při výsuvu z vřeteníku. Použita je metoda měření sklonu s imitovanou závislostí na deformaci nosiče měřené soustavy...
Contribution to ASPIICS Coronagraph on PROBA3
Melich, Radek; Psota, Pavel; Steiger, Lukáš; Vít, Tomáš; Kovačičinová, Jana
2013 - anglický
The aim of the document is to present design and technical notes on evaluation, manufacturing, and measurement of individual components and assembly methods of the Optical Objectives Assembly (OOA) of ASPIICS coronagraph for PROBA3.
Klíčová slova:
ASPIICS; optical design; PROBA3
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Contribution to ASPIICS Coronagraph on PROBA3
The aim of the document is to present design and technical notes on evaluation, manufacturing, and measurement of individual components and assembly methods of the Optical Objectives Assembly (OOA) of ...
Toptec Welding Process Visualization Instrument
Vojtíšek, Petr
2013 - anglický
MAG welding is characterized by very rapid processes in extreme condition of electric arc. To describe welding is necessary to use sufficiently quick equipment. Especially in the transition region between dip and spray transfer the processes develop quickly. Characterization of transition area in active three component shielding gas was carried out visually by hi speed camera equipment and electrically by quick response electronic measurement system
Klíčová slova:
Welding visualiation
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Toptec Welding Process Visualization Instrument
MAG welding is characterized by very rapid processes in extreme condition of electric arc. To describe welding is necessary to use sufficiently quick equipment. Especially in the transition region ...
Zpracování studie vlivu nejistot měření při kontrole optických ploch s cílem stanovit celkový úhrn chyb a doporučit postupy pro jejich minimalizaci
Lédl, Vít; Psota, Pavel
2013 - český
Pro účely vývoje přesných měřidel a měřících metod založených na optických principech je provedena analýza vlivu nejistot měření a zdrojů chyb. Je provedeno experimentální ověření odvozených závislostí. V závěru je shrnuta řada doporučení pro minimalizaci nejistot měření. For the purpose of development of precision instruments and measuring methods based on optical principles there is an analysis of the measurement uncertainties and error sources made. Experimental verification of derived dependencies is done. In conclusion summarization of a series of recommendations to minimize measurement uncertainties is made.
Klíčová slova:
measurement uncertainty; error; interference
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Zpracování studie vlivu nejistot měření při kontrole optických ploch s cílem stanovit celkový úhrn chyb a doporučit postupy pro jejich minimalizaci
Pro účely vývoje přesných měřidel a měřících metod založených na optických principech je provedena analýza vlivu nejistot měření a zdrojů chyb. Je provedeno experimentální ověření odvozených ...
Simulace optické soustavy depozičního monitoru
Doleček, Roman; Pintr, Pavel; Václavík, Jan
2013 - český
Zpráva popisuje výsledek modelování stávajícího vysílací a přijímací optické soustavy systému pro monitorování procesu vakuové depozice. Výsledek je diskutován s pozorovanými vlastnostmi systému, zejména chování pro různé vlnové délky a optická propustnost. Na základě analýzy je provedena matematická optimalizace nastavení komponent systému s cílem zlepšení výkonu a robustnosti. The report describes results of modeling of optical system which is component of optical monitoring system applied on machines for vacuum thin film deposition. Results were compared to real behavior of system, especially chromatic properties and total throughput. A numerical optimization, based on analysis results, was performed in order to improve throughput and ruggedness of the system.
Klíčová slova:
thin film; optical monitoring; simulation; optimalization
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Simulace optické soustavy depozičního monitoru
Zpráva popisuje výsledek modelování stávajícího vysílací a přijímací optické soustavy systému pro monitorování procesu vakuové depozice. Výsledek je diskutován s pozorovanými vlastnostmi systému, ...
Design, manufacture and test of M1 and M2 mirror production
Lédl, Vít; Melich, Radek; Pintr, Pavel; Polák, Jaroslav; Procháska, František; Psota, Pavel; Rail, Zdeněk; Steiger, Lukáš; Tomka, David; Václavík, Jan; Vápenka, David; Vít, Tomáš; Bartoníček, Jiří
2013 - anglický
Design and tests for realization of M1 and M2 mirrors for METIS project.
Klíčová slova:
METIS; lightweingted mirrors; low microroughness
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Design, manufacture and test of M1 and M2 mirror production
Design and tests for realization of M1 and M2 mirrors for METIS project.
Preliminary design of imaging system without zoom
Melich, Radek; Lédl, Vít
2012 - anglický
The aim of the report is to provide the preliminary design and simulations of an imaging system without zoom in accordance to the provided mechanical dimensions. The simulations will result in spot diagrams for various field objects. Finally, the optical transmission efficiency for optical design will be provided. All designed systems will be discussed with respect to their simulated performances and recommendation for final selected system will be provided.
Klíčová slova:
imaging system; electron beam microscopy
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Preliminary design of imaging system without zoom
The aim of the report is to provide the preliminary design and simulations of an imaging system without zoom in accordance to the provided mechanical dimensions. The simulations will result in spot ...
Studie: Svěšování vřetene
Pintr, Pavel; Psota, Pavel; Václavík, Jan
2012 - český
Studie shrnuje analýzu možných řešení měření svěšení vřetene horizontálního obráběcího stroje při zatížení nástrojem. Analyzovány byly optické metody využívající deflexe laserového svazku a analýzy stopy svazku na stínítku dvojice kamer. Byla též analyzována autokolimační metoda. Součástí studie jsou i oprické simulace situace provedené v prostředí Zemax a matematické výpočty deflexe, pohybu stopy a odhadované citlivosti. The study concludes with an analysis of possible measurement solutions droop horizontal spindle machine tool load. Were analyzed using optical methods deflection of the laser beam and analysis of the beam pattern on the screen two cameras. Was also analyzed autocollimation method. The study also includes oprické simulation situation made Zemax environment and mathematical calculations deflection, motion track and the estimated sensitivity
Klíčová slova:
spindle bending; laser; deflection; analysis; optical simulation
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Studie: Svěšování vřetene
Studie shrnuje analýzu možných řešení měření svěšení vřetene horizontálního obráběcího stroje při zatížení nástrojem. Analyzovány byly optické metody využívající deflexe laserového svazku a analýzy ...
NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.
Vaše náměty a připomínky posílejte na email nusl@techlib.cz
Provozovatel
Zahraniční báze