Počet nalezených dokumentů: 620
Publikováno od do

The role of solvents in the preparation of hydrophobic nanofibrous membrane containing fumed silica
Peer, Petra; Polášková, M.; Musilová, I.; Filip, Petr
2018 - anglický
It is well-known that a type of used fumed silica nanoparticles plays a dominant role in wettability of the corresponding nanofibrous mats. As a result, the desired contact angle can be approximately achieved by a choice of adequate fumed silica nanoparticles. However, less attention has been hitherto paid to an active role of solvents in connection with the tailoring this contact angle. For analysis we used poly(vinyl butyral) representing electrospun-friendly material, various types of fumed silica nanoparticles and two solvents - methanol and ethanol. It is demonstrated that a choice of polymer solvents plays a significant role in contact angle changes. Hence, in combination of the type of fumed silica nanoparticles and the type of solvent it is possible to achieve a finer partition of the required contact angles. Klíčová slova: PVB solution; solvents; fumed silica; electrospinning; rheology Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
The role of solvents in the preparation of hydrophobic nanofibrous membrane containing fumed silica

It is well-known that a type of used fumed silica nanoparticles plays a dominant role in wettability of the corresponding nanofibrous mats. As a result, the desired contact angle can be approximately ...

Peer, Petra; Polášková, M.; Musilová, I.; Filip, Petr
Ústav pro hydrodynamiku, 2018

Thermal induced morphological changes of poly(ethylene oxide) nanofibrous webs
Polášková, M.; Peer, Petra; Ponížil, P.; Čermák, R.
2018 - anglický
The crystallinity of fibres prepared by electrospinning shows lower level in comparison with samples processed by common technologies such as moulding or film casting. Thus, the attempts to improve the structure of electrospun fibres in order to increase physical and mechanical properties of nonwoven webs are obvious. Post-process thermal treatment is one of the possibilities of the crystallinity enhancement that can be easily included to the finishing operation of final products. For the experiment we used poly(ethylene oxide) representing electrospun-friendly material and two solvents - methanol and water, both ensuring good electrospinnability. It is demonstrated that a choice of polymer solvents plays a significant role in fibre diameter and their capabilities to resist applied heat. However, in all cases the enhancement of crystallinity is detected at the short time of thermal exposure. Klíčová slova: PEO nanofibres; degree of crystallinity; electrospinning Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Thermal induced morphological changes of poly(ethylene oxide) nanofibrous webs

The crystallinity of fibres prepared by electrospinning shows lower level in comparison with samples processed by common technologies such as moulding or film casting. Thus, the attempts to improve ...

Polášková, M.; Peer, Petra; Ponížil, P.; Čermák, R.
Ústav pro hydrodynamiku, 2018

Modelling of non-monotonous course of shear viscosity
Filip, Petr
2018 - anglický
A number of parameters appearing in the 'classical' empirical constitutive equations usually oscillate between two and five. With the onset of new rheologically more complex materials exhibiting non-monotonous behaviour of flow curves this range (2-5) is no longer tenable and more additional parameters are required for a proper description of the flow curves. An 8-parameter model is presented and testified. Klíčová slova: viscosity; flow curve; constitutive equation; empirical modelling Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Modelling of non-monotonous course of shear viscosity

A number of parameters appearing in the 'classical' empirical constitutive equations usually oscillate between two and five. With the onset of new rheologically more complex materials exhibiting ...

Filip, Petr
Ústav pro hydrodynamiku, 2018

Redukce šumu z experimentálních časových řad
Chára, Zdeněk; Kysela, Bohuš
2018 - český
Příspěvek se zabývá redukcí šumu z časových řad. Pozornost je zaměřena především na časové řady získané metodou PIV. Metoda redukce šumu je testována pro PIV data získaná při měření rychlostních polí v míchané nádobě. This article deals with the denoising of experimental time series. Attention is focused primarily on the time series obtained by the PIV method. The noise reduction method is tested for the PIV data obtained by measuring the velocity fields in the stirred vessel. Klíčová slova: denoising; PIV; time series Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Redukce šumu z experimentálních časových řad

Příspěvek se zabývá redukcí šumu z časových řad. Pozornost je zaměřena především na časové řady získané metodou PIV. Metoda redukce šumu je testována pro PIV data získaná při měření rychlostních polí ...

Chára, Zdeněk; Kysela, Bohuš
Ústav pro hydrodynamiku, 2018

The importance of the radiation balance for water retention of the landscape
Kofroňová, Jitka
2018 - anglický
As part of the radiation balance, longwave radiation is one of the factors needed to estimate potential evapotranspiration (PET). Since the longwave radiation balance is rarely measured, many computational methods have been designed. In this study, we report on the difference between the observed longwave radiation balance and modelling results obtained using the two main procedures outlined in Manuals 24 and 56 of the FAO. The performance of these equations was evaluated in the warmer months (April to October) over eight years at the Liz experimental catchment in the Bohemian Forest (Czech Republic). The coefficients of both methods were also calibrated based on local conditions. Four commonly used methods were used to calculate the PET (Penman-Monteith, Pristley and Taylor, Kimberley-Penman, Thom and Oliver). The use of default coefficient values gave errors of 40 100 mm and 0 20 mm for the seasonal PET estimates for FAO56 and FAO24, respectively (the PET was usually overestimated). Parameter calibration decreased the FAO56 error to less than 20 mm per season (FAO24 remained unaffected by the calibration). The FAO56 approach with calibrated coefficients proved to be more suitable for estimation of the longwave radiation balance. Klíčová slova: water retention; radiation balance; potential evapotranspiration (PET) Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
The importance of the radiation balance for water retention of the landscape

As part of the radiation balance, longwave radiation is one of the factors needed to estimate potential evapotranspiration (PET). Since the longwave radiation balance is rarely measured, many ...

Kofroňová, Jitka
Ústav pro hydrodynamiku, 2018

Image analysis of particle size: effect of light source type
Formánek, R.; Kysela, Bohuš; Šulc, R.
2018 - anglický
Agitation of two immiscible liquids or solid-liquid suspension is a frequent operation in chemical and metallurgical industries. The sizes of particles, bubbles or droplets can be determined by the Image Analysis Technique. It is known that the quality of captured images depends significantly on the original image background that is mainly affected by the type of the light source. The aim of this contribution is to investigate the effect of light source type on image quality. The four types of light sources were tested: 1) 1000 W halogen lamp, 2) 72 W LED bar panel, 3) 60 W LED chip, and 4) 90 W LED chip. The illumination intensity and image background quality were investigated for each tested light sources. The effect of the shutter speed on evaluated particle sizes was tested using monodisperse spherical calibration particles having diameter of 1.19 mm. The difference observed between particle sizes evaluated by image analysis for given light source and declared calibration particle diameter was used as a measure of light source quality. Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Image analysis of particle size: effect of light source type

Agitation of two immiscible liquids or solid-liquid suspension is a frequent operation in chemical and metallurgical industries. The sizes of particles, bubbles or droplets can be determined by the ...

Formánek, R.; Kysela, Bohuš; Šulc, R.
Ústav pro hydrodynamiku, 2018

Settling slurry flow near deposition velocity in inclined pipe of negative slope
Kesely, Mikoláš; Matoušek, Václav; Vlasák, Pavel
2018 - anglický
Pipe flow of sand-water slurry (settling slurry) is sensitive to pipe inclination. The effect of the angle to which the partially stratified flow is inclined from the horizontal has been subject to investigation in numerous studies. However, almost all of them focus on ascending flows, i.e. flows inclined to positive angles of inclination. It is well known that settling slurry flows inclined to negative slopes (descending flows) differ from those inclined to positive slopes, particularly at velocities near the deposition limit. The deposition limit velocity is the flow velocity at which stationary deposit starts to be formed at the bottom of the pipe. We investigate the effect of the negative slope on pipe flow near deposition limit velocity in the broad range of inclination angles. Besides the deposition limit, we focus on the distribution of solids across the pipe cross section. We combine experimental approach with mathematical modelling. Our new experiments with medium-to-coarse sand (mass-medium grain size 0.87 mm) in a 100-mm pipe inclined from 0 to -45 degree provide suitable data for a validation of predictions of our layered model for partially stratified flows in inclined pipes. Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Settling slurry flow near deposition velocity in inclined pipe of negative slope

Pipe flow of sand-water slurry (settling slurry) is sensitive to pipe inclination. The effect of the angle to which the partially stratified flow is inclined from the horizontal has been subject to ...

Kesely, Mikoláš; Matoušek, Václav; Vlasák, Pavel
Ústav pro hydrodynamiku, 2018

Koagulace rozdílných typů látek ze sinic a řas
Novotná, Kateřina; Načeradská, Jana; Barešová, Magdalena; Janda, V.; Pivokonský, Martin
2018 - český
Příspěvek se zabývá charakterizací a koagulací rozdílných typů látek produkovaných fytoplanktonem (algal organic matter - AOM), zejména jejich neproteinovou složkou, tvořenou sacharidy aj. Tyto látky byly získány z celulárního organického materiálu zelené řasy Chlorella vulgaris. Při koagulaci neproteinových AOM byla testována dvě různá koagulační činidla na bázi hliníku (síran hlinitý - SH a polyaluminiumchlorid - PACI). Nejúčinnější koagulace bylo v obou případech dosaženo v oblasti kolem neutrálního pH (7,1-7,5 a 7,6-8,0 při použití SH a PACI, resp.), přičemž byly zapotřebí poměrně vysoké dávky činidla (8 a 10 mg.L-1 Al, resp.). I při optimalizovaných podmínkách koagulace však bylo odstraněno max. cca 20% neproteinových AOM. Vhodné podmínky, účinnost i mechanismy koagulace neproteinové složky se značně liší od těch pro AOM peptidy/proteiny, což souvisí s rozdílnými vlastnostmi daných skupin látek (distribuce molekulových hmotností, množství a charakter povrchových funkčních skupin atd.). Pro účinnou optimalizaci koagulace je tedy rozhodující nejen koncentrace, ale právě i charakter AOM. This study focused on coagulation of different algal organic matter (AOM) fractions, especially on its non-proteinaceous fraction. It was derived from cellular organic matter of Chlorella vulgaris, a freshwater algae. Two different Al-based coagulants were employed, i.e. alum and pre-hydrolyzed polyaluminim chloride (PACl). The highest coagulation efficiency was obtained at pH around neutral (pH 7.1-7.5 for alum and pH 7.6-8.0 for PACl) at relatively high dosages of coagulant (8 and 10 mg·L-1 as Al for alum and PACl, resp.). However, the maximum removal reached under the optimized conditions was only approximately 20%. The coagulation behaviour and efficiency of non-proteinaceous matter greatly differ from AOM peptide-proteins, which is discussed in the study. Klíčová slova: algal organic matter; Chlorella vulgaris; coagulation; water treatment Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Koagulace rozdílných typů látek ze sinic a řas

Příspěvek se zabývá charakterizací a koagulací rozdílných typů látek produkovaných fytoplanktonem (algal organic matter - AOM), zejména jejich neproteinovou složkou, tvořenou sacharidy aj. Tyto látky ...

Novotná, Kateřina; Načeradská, Jana; Barešová, Magdalena; Janda, V.; Pivokonský, Martin
Ústav pro hydrodynamiku, 2018

Vyhodnocení průtoku přes měřící objemem při měření velikosti kapek
Kysela, Bohuš; Formánek, R.; Chára, Zdeněk; Konfršt, Jiří; Jašíková, D.; Šulc, R.
2018 - český
Měření a vyhodnocení velikosti kapek prostřednictvím obrazové analýzy (IA) bylo široce používáno v mnoha výzkumech. Vývoj nových vizualizačních technik a PIV metod umožňuje měřit přímo v kontrolním objemu. Tyto metody jsou však omezeny následujícími parametry, jako je velikost snímané oblasti, maximální rozlišení a optická omezení (průhlednost, index lomu, koncentrace dispergované fáze). Tento příspěvek je zaměřen na simulaci rychlostního pole ve snímané oblasti zájmu, které slouží k nastavení důležitých parametru kamery. The in-situ measurement and evaluation of drop sizes via Image Analysis (IA) has been widely used by many researches. The development of new visualization techniques and PIV methods enables to measure directly in a control volume. However, these methods are limited by following parameters such as size of the scanned area, maximal resolution and optical limitations (transparency, refractive index, concentration of dispersed phase). This contribution is focused on simulation of velocity field in region of interest which serve for determine the important parameters of camera setting. Klíčová slova: drop size; region of interest; shutter time; frame rate; focus depth; liquid-liquid dispersion Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Vyhodnocení průtoku přes měřící objemem při měření velikosti kapek

Měření a vyhodnocení velikosti kapek prostřednictvím obrazové analýzy (IA) bylo široce používáno v mnoha výzkumech. Vývoj nových vizualizačních technik a PIV metod umožňuje měřit přímo v kontrolním ...

Kysela, Bohuš; Formánek, R.; Chára, Zdeněk; Konfršt, Jiří; Jašíková, D.; Šulc, R.
Ústav pro hydrodynamiku, 2018

Mohou sinice zlepšit úpravu pitné vody? Sci-fi nebo realita?
Barešová, Magdalena; Načeradská, Jana; Novotná, Kateřina; Pivokonská, Lenka; Pivokonský, Martin
2018 - český
Úprava pitné vody se potýká s výskytem sinic a řas především sezónně a to zejména ve fázi jejich odumírání, kdy dochází k uvolnění značného množství celulárních organických látek (COM – Cellular Organic Matter). Vzhledem k tomu, že COM jsou nejen obtížně odstranitelné, ale ovlivňují i odstranitelnost dalších znečišťujících příměsí, cílem výzkumu bylo zhodnotit vliv COM extrahovaných ze dvou druhů běžně se vyskytujících sinic – Microcystis aeruginosa a Merismopedia tenuissima na koagulaci dalších přírodně se vyskytujících částic a látek přítomných v povrchových vodách: kaolinové suspenze, huminových látek a buněk M. tenuissima. Bylo prokázáno, že vyšší koncentrace COM nezbytně nevedou k narušení koagulace. V případě, že COM interagují s dalšími znečišťujícími příměsi, mohou tyto interakce vést naopak ke snížení dávek koagulantu a zvýšení účinnosti odstranění nejen zákalu ale i efektivnější koagulaci huminových látek. Drinking water treatment struggles with cyanobacteria and algae mainly on a seasonal basis especially when they decay and release amounts of cellular organic matter (COM). As COM is not only difficult to be removed but it also impacts the removability of other impurities, this paper aims to evaluate the effect of COM derived from two common cyanobacterial species– Microcystis aeruginosa and Merismopedia tenuissima on coagulation of other naturally occurring particles and molecules present in surface waters: kaolin suspension, humin substances and cells of M. tenuissima. Our findings show that higher COM concentrations do not have to disrupt coagulation. When COM interacts with other impurities, it can even lower coagulant doses and increase both turbidity and humic matter removal efficiencies. Klíčová slova: algal organic matter; coagulation; cyanobacteria; drinking water treatment; humic substances; kaolin Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Mohou sinice zlepšit úpravu pitné vody? Sci-fi nebo realita?

Úprava pitné vody se potýká s výskytem sinic a řas především sezónně a to zejména ve fázi jejich odumírání, kdy dochází k uvolnění značného množství celulárních organických látek (COM – Cellular ...

Barešová, Magdalena; Načeradská, Jana; Novotná, Kateřina; Pivokonská, Lenka; Pivokonský, Martin
Ústav pro hydrodynamiku, 2018

O službě

NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.

Vaše náměty a připomínky posílejte na email nusl@techlib.cz

Provozovatel

http://www.techlib.cz

Facebook

Zahraniční báze