No (20977)
Number of found documents:
20977
Published from
to
Computational and experimental assessment of natural frequencies in a bladed disk system
Mekhalfia, Mohammed Lamine; Procházka, Pavel; Maturkanič, Dušan; Voronova, Evgeniya; Hodboď, Robert
2024 - English
This paper examines the modal characteristics of a bladed disk in rotating machinery systems using a combination of analytical and experimental modal analysis methods. The analysis involves measuring natural frequencies and mode shapes under different operational conditions. A comparative analysis is conducted to assess modal properties obtained from both analytical and experimental approaches, while also considering the influence of rotation speed. Additionally, Finite Element Method (FEM) outputs are used to accurately position the strain gauge. Integrating these techniques provides a comprehensive understanding of the bladed disk's behaviour under varying rotational speeds, enhancing result accuracy and facilitating thorough investigation within rotating machinery systems.
Keywords:
natural frequencies; FEM; LDV; strain gauge
Available at various institutes of the ASCR
Computational and experimental assessment of natural frequencies in a bladed disk system
This paper examines the modal characteristics of a bladed disk in rotating machinery systems using a combination of analytical and experimental modal analysis methods. The analysis involves measuring ...
Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding
Šebestová, Hana; Horník, Petr; Mika, Filip; Mikmeková, Šárka; Ambrož, Ondřej; Mrňa, Libor
2024 - English
Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. When the coated sheets are welded, the effect of the chemical composition of the coating must be also considered even though its thickness is only a few tens of microns. During 22MnB5+AlSi laser welding experiments, the ferrite-stabilizing elements of coating modified the weld metal microstructure. Ferrite appeared in a quenched weld metal. The rapid cooling rate accompanying welding with a focused beam limited the homogenization of the weld metal which resulted in the formation of ferritic bands in the regions rich in Si and especially in Al. On the other hand, a high level of homogenization was reached when welding with the defocused beam. The ferritic islands uniformly distributed in the weld metal were formed at 0.4 wt% and 1.6 wt% of Si and Al, respectively. The doubled heat input reduced the Al content to 0.7 wt% insufficient for the ferrite formation at still relatively high cooling rates. Predicting the distribution of ferrite in the weld metal is challenging due to its dependence on various factors, such as cooling rate and the volume of dissolved coating, which may vary with any modifications made to the welding parameters.
Keywords:
laser welding; high-strength steel; microstructure; heat input; ferrite stabilization
Available at various institutes of the ASCR
Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding
Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. ...
Influence of ball material on the resulting fatigue life of thermal sprayed HVOF coatings in dynamic impact testing
Duliškovič, J.; Daniel, Josef; Houdková, Š.
2024 - English
Dynamic impact wear, i.e. contact between two components in the presence of high cyclic local loads, is a challenging failure mode that occurs in many mechanical applications. Many previous studies have confirmed that dynamic impact testing is suitable for evaluating the contact fatigue of thermal sprayed coatings. However, the effect of the test parameters on the resulting lifetime is unclear. The aim of this study describes the effect of the ball material used in the dynamic impact test on the resulting fatigue life of the HVOF thermal sprayed coating. Three test balls made of WC/Co alloy, Si3N4 silicon nitride and 440 C steel were chosen for this study. Dynamic impaction testing was carried out on the Cr3C2-NiCr coating, which was sprayed by HVOF on a 1.2376 high-speed steel substrate. The impact lifetime was described by the number of critical impacts, i.e. the number of impacts before coating fatigue occurs. Furthermore, the depth and volume of impact craters were measured. Using scanning electron microscopy (SEM), the surface of the impacts as well as the microstructure of the coating on the cross-section in the region of the impacts were observed. Furthermore, the mechanism of crack propagation in the coating and the microstructure of the indentor were investigated.
Keywords:
dynamic impact test; HVOF; Cr3C2-NiCr; fatigue
Available at various institutes of the ASCR
Influence of ball material on the resulting fatigue life of thermal sprayed HVOF coatings in dynamic impact testing
Dynamic impact wear, i.e. contact between two components in the presence of high cyclic local loads, is a challenging failure mode that occurs in many mechanical applications. Many previous studies ...
Functional Tungsten-based thin films and their characterization
Košelová, Zuzana; Horáková, L.; Sobola, Dinara; Burda, Daniel; Knápek, Alexandr; Fohlerová, Z.
2024 - English
Anodizing is a technique by which thin oxide layers can be formed on a surface. Thin oxide layers have been found to be useful in a variety of applications, including emitters of electrons. Tungsten is still a common choice for cold field emitters in commercial microscopy applications. Its suitable quality can be further improved by thin film deposition. Not only the emission characteristic can be improved, but also the emitter operating time can be extended. Tungsten oxide is known for its excellent resistance to corrosion and chemical attack due to its stable crystal structure and strong chemical bonds between tungsten and oxygen atoms. Many techniques with different advantages and disadvantages have been used for this purpose. Anodization was chosen for this work because of the controllable uniform coverage of the material and its easy availability without the need for expensive complex equipment. The anodizing process involves applying an electrical potential to tungsten while it is immersed in an electrolyte solution. This creates a thin layer of tungsten oxide on the surface of the metal. The thickness and properties of the resulting oxide layer can be controlled by adjusting the anodization conditions, such as the electrolyte solution, voltage, and the duration of the process. In this work, H3PO4 was used as the electrolyte to test whether these tungsten oxide layers would be useful for electron emitters, for use in electron guns and other devices that require high-quality electron emitters. The properties were evaluated using appropriate techniques. In general, anodization of tungsten to form thin layers of tungsten oxide layers is a promising technique for producing high quality electron emitters.
Keywords:
cold-field emission; thin layer deposition; tungsten oxide; resonance enhanced tunneling; anodization
Available at various institutes of the ASCR
Functional Tungsten-based thin films and their characterization
Anodizing is a technique by which thin oxide layers can be formed on a surface. Thin oxide layers have been found to be useful in a variety of applications, including emitters of electrons. Tungsten ...
Využití termografie v průzkumech památek
Valach, Jaroslav; Eisler, Marek
2024 - Czech
Termografie rozšiřuje portfolia metod, jimiž lze studovat vlastnosti objektů okolního světa. Ještě před deseti lety byla tato technologie kvůli potenciálním vojenským aplikacím úzkostlivě kontrolována, což omezovalo konkurenci v nabídce výrobků a výrobců a vedlo k vysokým cenám zařízení založených na těchto principech. Teprve díky uvolnění této kontroly došlo k rozmachu výroby a zpřístupnění zjednodušených výrobků masovému využití, takže si dnes může zákazník například pořídit chytrý telefon s doplňkovým termografickým modulem jen s malým navýšením ceny. Spolu s dostupností zařízení pozorujeme nárůst uplatnění termografie v mnoha oblastech, včetně průzkumů staveb a památek. Thermography expands the portfolio of methods that can be used to study the properties of objects in the surrounding world. As recently as a decade ago, the technology was frowned upon for potential military applications controlled, which limited competition in the offer of products and manufacturers and led to high prices of devices based on these principles. It was only thanks to the release of this control that it happened to expand production and make simplified products available to mass use, so get it today for example, a customer can purchase a smartphone with an additional thermographic module for only with a small price increase. Together with the availability of equipment, we observe an increase in the application of thermography in many areas, including surveys of buildings and monuments.
Keywords:
thermography; survey of historical structures
Available at various institutes of the ASCR
Využití termografie v průzkumech památek
Termografie rozšiřuje portfolia metod, jimiž lze studovat vlastnosti objektů okolního světa. Ještě před deseti lety byla tato technologie kvůli potenciálním vojenským aplikacím úzkostlivě ...
Verification of the dynamic properties of a new model turbine wheel with free blades
Voronova, Evgeniya; Procházka, Pavel; Maturkanič, Dušan; Mekhalfia, Mohammed Lamine; Hodboď, Robert
2024 - English
The paper describes a new experimental model of turbine wheel with free blades. Verification tests were carried out using a Doppler laser vibrometer, with a focus on the equipment parameters under various conditions. The measurements were performed in the Laboratory of Rotational Laser Vibrometry originated at the Institute of Thermomechanics AS CR, v.v.i.
Keywords:
natural frequencies; vibration; blade; laser; turbine
Available at various institutes of the ASCR
Verification of the dynamic properties of a new model turbine wheel with free blades
The paper describes a new experimental model of turbine wheel with free blades. Verification tests were carried out using a Doppler laser vibrometer, with a focus on the equipment parameters under ...
Česká putování za Richardem Wagnerem
Fránek, Michal; Kopecký, J.
2024 - Czech
Studie zkoumá fenomén českých cest za slavným německým skladatelem Richardem Wagnerem a do míst spojených s jeho kultem (Mnichov, Bayreuth, Curych atd.). Zaměřuje se na wagnerovské cesty – uskutečněné i neuskutečněné – českých skladatelů (Bedřich Smetana, Antonín Dvořák, Zdeněk Fibich, Josef Bohuslav Foerster), interpretů (Ema Destinnová, Karel Burian aj.), hudebních kritiků (Otakar Hostinský, V. V. Zelený), malířů (Jaroslav Čermák) a spisovatelů (Julius Zeyer, Jaroslav Maria, Teréza Nováková), přičemž sleduje jejich různé motivace. The study explores the phenomenon of Czech travels to famous German composer Richard Wagner and to the places associated with his cult (Munich, Bayreuth, Zurich, etc.). It focuses on the Wagnerian journeys – accomplished and not – of Czech composers (Bedřich Smetana, Antonín Dvořák, Zdeněk Fibich, Josef Bohuslav Foerster), performers (Ema Destinnová, Karel Burian, etc.), music critics (Otakar Hostinský, V. V. Zelený), painters (Jaroslav Čermák) and writers (Julius Zeyer, Jaroslav Maria, Teréza Nováková), tracing their different motivations.
Keywords:
Richard Wagner; travelling to artists
Available at various institutes of the ASCR
Česká putování za Richardem Wagnerem
Studie zkoumá fenomén českých cest za slavným německým skladatelem Richardem Wagnerem a do míst spojených s jeho kultem (Mnichov, Bayreuth, Curych atd.). Zaměřuje se na wagnerovské cesty – uskutečněné ...
Železniční cestovatel Eduard Bazika aneb Cestování s manželkou
Hlavačka, Milan
2024 - Czech
Ing. Eduard Bazika (1830–1914) nebyl profesionální poutník, ale poutník z profese. Jako absolvent pražské polytechniky se celý život specializoval na železniční stavitelství a jako inženýr nejdříve státních drah a od roku 1855 až do odchodu na odpočinek v roce 1891 soukromé Společnosti státní dráhy (StEG) celý život procestoval, respektive před výstavbou prochodil svěřené železnice v české a moravské krajině. I po odchodu na penzi pracoval pro Zemský výbor Království českého a jeho Železniční výbor a v této pozici opět pracovně putoval po všech koutech Čech, aby posuzoval rentabilitu budoucích místních drah. Jeho zvláštností bylo, že se vždy snažil skloubit své cestovní povinnosti s rodinným životem, což mělo za následek, že jeho žena a děti putovaly s ním po nejrůznějších štacích a železničních stavbách. Stranou neponechával ani dlouhodobější náročnější soukromé cesty s manželkou na světové výstavy a po historických památkách Itálie (v doprovodu Jiřího Stibrala) či k obhlídce nově dokončených alpských železnicích. Jako představitel sebevědomé české střední třídy, která už disponovala volným časem a finančními prostředky (a samozřejmě režijní jízdenkou) dovedl skloubit cestovatelskou povinnost s cestovatelskou vášní a putování vnímal jako nezbytnou součást aktivního životního stylu moderního člověka. Ing. Eduard Bazika (1830–1914) was not a professional pilgrim, but a pilgrim by profession. As a graduate of the Prague Polytechnic, he specialized in railway construction all his life and as an engineer, first of all for the State railways, and from 1855 until his retirement in 1891, he traveled all his life for the private State Railway Company (StEG), or rather, before construction, he traveled the entrusted railways in the Bohemian and Moravian landscape. Even after retiring, he worked for the Land Committee of the Kingdom of Bohemia and its Railway Committee, and in this position he once again traveled to all corners of Bohemia to assess the profitability of future local railways. A peculiarity of his was that he always tried to combine his traveling duties with his family life, which resulted in his wife and children traveling with him to various estates and railway constructions. He did not leave aside longer, more demanding private trips with his wife to world exhibitions and historical monuments in Italy (accompanied by Jiří Stibral) or to inspect the newly completed Alpine railways. As a representative of the self-confident Czech middle class, who already had free time and financial resources (and, of course, an overhead ticket), he was able to combine the obligation to travel with a passion for travel and perceived traveling as a necessary part of the active lifestyle of a modern person.
Keywords:
Ing Eduard Bazika; pilgrim by profession; railway
Available at various institutes of the ASCR
Železniční cestovatel Eduard Bazika aneb Cestování s manželkou
Ing. Eduard Bazika (1830–1914) nebyl profesionální poutník, ale poutník z profese. Jako absolvent pražské polytechniky se celý život specializoval na železniční stavitelství a jako inženýr nejdříve ...
Modification of cooling system for laboratory measurement of rotor blade vibration
Maturkanič, Dušan; Procházka, Pavel; Hodboď, Robert; Voronova, Evgeniya; Mekhalfia, Mohammed Lamine
2024 - English
Last year, the replacement of the turbine wheel model was completed in the Laboratory of Rotational Laser Vibrometry of the Institute of Thermomechanics AS CR, v.v.i. Based on previous experience and the expected higher operating load planned for the new wheel, the cooling system was modified at the same time. The paper describes the main effort in this direction and the results that clarify the previous damage of the measuring device.
Keywords:
blade; vibration; cooling system; measurement; laboratory
Available at various institutes of the ASCR
Modification of cooling system for laboratory measurement of rotor blade vibration
Last year, the replacement of the turbine wheel model was completed in the Laboratory of Rotational Laser Vibrometry of the Institute of Thermomechanics AS CR, v.v.i. Based on previous experience and ...
PROPERTIES OF NANOCRYSTALLINE FE-NI PARTICLES PREPARED BY THERMAL REDUCTION OF OXALATE PRECURSORS
Švábenská, Eva; Roupcová, Pavla; Havlíček, Lubomír; Schneeweiss, Oldřich
2024 - English
Recent technological advancements require development of cost-effective and high-performance magnets \nwhich ideally do not contain rare earth metals or noble metals. The promising candidates are Fe-Ni-based \nalloys, in particular, the Fe50Ni50 L10 phase (tetrataenite), which has a great perspective for producing hard \nmagnetic materials. Our study explores a promising method for preparing nanoparticles of Fe-Ni alloy from an \niron-nickel oxalate precursor. The coprecipitation method was employed to prepare oxalate precursors, \nfollowed by controlled thermal decomposition in a reducing hydrogen atmosphere. The morphology and \nproperties of the resulting particles were analysed using scanning electron microscopy (SEM) coupled with \nenergy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Mössbauer spectroscopy (MS), and \nmagnetic measurements.\nThe SEM analysis revealed that the particles have approximately cube-shaped unit cell morphology with a\nsize in a range of 1 - 2 μm. Upon annealing, the samples contain multiple phases with varying Fe-Ni content.\nMagnetic measurements confirmed the formation of magnetically suitable Fe-Ni phases in the samples after \nannealing. Mössbauer spectroscopy emerged as a highly effective method for characterizing individual phases \nof the Fe-Ni system.
Keywords:
Magnetic materials; thermal decomposition; Mössbauer spectroscopy
Available at various institutes of the ASCR
PROPERTIES OF NANOCRYSTALLINE FE-NI PARTICLES PREPARED BY THERMAL REDUCTION OF OXALATE PRECURSORS
Recent technological advancements require development of cost-effective and high-performance magnets \nwhich ideally do not contain rare earth metals or noble metals. The promising candidates are ...
NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web
Send your suggestions and comments to nusl@techlib.cz
Provider
Other bases