Number of found documents: 10786
Published from to

Influence of ball material on the resulting fatigue life of thermal sprayed HVOF coatings in dynamic impact testing
Duliškovič, J.; Daniel, Josef; Houdková, Š.
2024 - English
Dynamic impact wear, i.e. contact between two components in the presence of high cyclic local loads, is a challenging failure mode that occurs in many mechanical applications. Many previous studies have confirmed that dynamic impact testing is suitable for evaluating the contact fatigue of thermal sprayed coatings. However, the effect of the test parameters on the resulting lifetime is unclear. The aim of this study describes the effect of the ball material used in the dynamic impact test on the resulting fatigue life of the HVOF thermal sprayed coating. Three test balls made of WC/Co alloy, Si3N4 silicon nitride and 440 C steel were chosen for this study. Dynamic impaction testing was carried out on the Cr3C2-NiCr coating, which was sprayed by HVOF on a 1.2376 high-speed steel substrate. The impact lifetime was described by the number of critical impacts, i.e. the number of impacts before coating fatigue occurs. Furthermore, the depth and volume of impact craters were measured. Using scanning electron microscopy (SEM), the surface of the impacts as well as the microstructure of the coating on the cross-section in the region of the impacts were observed. Furthermore, the mechanism of crack propagation in the coating and the microstructure of the indentor were investigated. Keywords: dynamic impact test; HVOF; Cr3C2-NiCr; fatigue Available at various institutes of the ASCR
Influence of ball material on the resulting fatigue life of thermal sprayed HVOF coatings in dynamic impact testing

Dynamic impact wear, i.e. contact between two components in the presence of high cyclic local loads, is a challenging failure mode that occurs in many mechanical applications. Many previous studies ...

Duliškovič, J.; Daniel, Josef; Houdková, Š.
Ústav přístrojové techniky, 2024

Functional Tungsten-based thin films and their characterization
Košelová, Zuzana; Horáková, L.; Sobola, Dinara; Burda, Daniel; Knápek, Alexandr; Fohlerová, Z.
2024 - English
Anodizing is a technique by which thin oxide layers can be formed on a surface. Thin oxide layers have been found to be useful in a variety of applications, including emitters of electrons. Tungsten is still a common choice for cold field emitters in commercial microscopy applications. Its suitable quality can be further improved by thin film deposition. Not only the emission characteristic can be improved, but also the emitter operating time can be extended. Tungsten oxide is known for its excellent resistance to corrosion and chemical attack due to its stable crystal structure and strong chemical bonds between tungsten and oxygen atoms. Many techniques with different advantages and disadvantages have been used for this purpose. Anodization was chosen for this work because of the controllable uniform coverage of the material and its easy availability without the need for expensive complex equipment. The anodizing process involves applying an electrical potential to tungsten while it is immersed in an electrolyte solution. This creates a thin layer of tungsten oxide on the surface of the metal. The thickness and properties of the resulting oxide layer can be controlled by adjusting the anodization conditions, such as the electrolyte solution, voltage, and the duration of the process. In this work, H3PO4 was used as the electrolyte to test whether these tungsten oxide layers would be useful for electron emitters, for use in electron guns and other devices that require high-quality electron emitters. The properties were evaluated using appropriate techniques. In general, anodization of tungsten to form thin layers of tungsten oxide layers is a promising technique for producing high quality electron emitters. Keywords: cold-field emission; thin layer deposition; tungsten oxide; resonance enhanced tunneling; anodization Available at various institutes of the ASCR
Functional Tungsten-based thin films and their characterization

Anodizing is a technique by which thin oxide layers can be formed on a surface. Thin oxide layers have been found to be useful in a variety of applications, including emitters of electrons. Tungsten ...

Košelová, Zuzana; Horáková, L.; Sobola, Dinara; Burda, Daniel; Knápek, Alexandr; Fohlerová, Z.
Ústav přístrojové techniky, 2024

Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding
Šebestová, Hana; Horník, Petr; Mika, Filip; Mikmeková, Šárka; Ambrož, Ondřej; Mrňa, Libor
2024 - English
Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. When the coated sheets are welded, the effect of the chemical composition of the coating must be also considered even though its thickness is only a few tens of microns. During 22MnB5+AlSi laser welding experiments, the ferrite-stabilizing elements of coating modified the weld metal microstructure. Ferrite appeared in a quenched weld metal. The rapid cooling rate accompanying welding with a focused beam limited the homogenization of the weld metal which resulted in the formation of ferritic bands in the regions rich in Si and especially in Al. On the other hand, a high level of homogenization was reached when welding with the defocused beam. The ferritic islands uniformly distributed in the weld metal were formed at 0.4 wt% and 1.6 wt% of Si and Al, respectively. The doubled heat input reduced the Al content to 0.7 wt% insufficient for the ferrite formation at still relatively high cooling rates. Predicting the distribution of ferrite in the weld metal is challenging due to its dependence on various factors, such as cooling rate and the volume of dissolved coating, which may vary with any modifications made to the welding parameters. Keywords: laser welding; high-strength steel; microstructure; heat input; ferrite stabilization Available at various institutes of the ASCR
Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding

Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. ...

Šebestová, Hana; Horník, Petr; Mika, Filip; Mikmeková, Šárka; Ambrož, Ondřej; Mrňa, Libor
Ústav přístrojové techniky, 2024

Room temperature ethanol detection using carbon materials
Kočí, Michal
2023 - English
Allotropic forms of carbon, in particular graphene oxide (GO) or nanocrystalline diamond (NCD), attracted the attention of many research groups due to their unique electronic structures and extraordinary physical and chemical properties, preferable for many different applications, including sensor devices. This work focuses on responses of various sensing layers (NCD with hydrogen termination (H-NCD), graphene oxide (GO), reduced graphene oxide (rGO), thiol-functionalized graphene oxide (GO-SH) and their hybrid structures to ethanol vapor with concentrations up to 100 ppm in synthetic air at room temperature. The measured parameters of the tested sensors, especially stability, reproducibility and regeneration, are compared and critically evaluated. The high sensitivity of tested sensors achieved at room temperature makes them very promising for monitoring ethanol vapor as well as other volatile substances (e.g., isopropyl-alcohol or acetone). Keywords: gas sensor; nanocrystalline diamond (NCD); graphene oxide (GO); reduced graphene oxide (rGO); thiol-functionalized graphene oxide (GO-SH) Available at various institutes of the ASCR
Room temperature ethanol detection using carbon materials

Allotropic forms of carbon, in particular graphene oxide (GO) or nanocrystalline diamond (NCD), attracted the attention of many research groups due to their unique electronic structures and ...

Kočí, Michal
Fyzikální ústav, 2023

Výzkum zříceniny hradu Štamberk v kontextu regionu
Novotný, Jakub; Ramešová, Michaela
2023 - Czech
Příspěvek přibližuje dosavadní výsledky výzkumu hradu Štamberk realizovaného dle nově definovaných zásad pro výzkum, správu a prezentaci historických zřícenin, jehož cílem je podpořit nová řešení jak zvýšit využitelnost hradu pro cestovní ruch a integrovat památku do regionálních struktur lokalit s potenciálem cestovního ruchu. Hrad byl významným panstvím v rámci území dnešní Vysočiny. Předmětem řešení projektu, na kterém od roku 2020 spolupracuje ÚTAM AV ČR s Mikroregionem Telčsko, je výzkum historie hradu se zaměřením na technologická hlediska jeho výstavby, stavebních změn i zániku. Součástí je vytvoření 3D modelu zříceniny v krajinném kontextu. Projekt se soustředí na dějiny výroby vápna a související inventarizaci geologických lokalit. Tento výzkum přináší nové informace důležité nejen pro poznání historie hradu či pro studium analogických situací, ale také pro zvýšení atraktivity památky pro cestovní ruch. Příspěvek nejprve představí aktuální standardy výzkumu a managementu zřícenin, následně se bude zabývat nástinem potenciálu výzkumu Štamberka pro oblast cestovního ruchu s důrazem na historii hradu, mapování krajinného rámce a identifikace vazeb na regionální prostředí. Na závěr zrekapituluje dosavadní výsledky využitelné k prezentaci historického, kulturního i přírodního bohatství regionu se specifickou vazbou na cestovní ruch. The paper provides an overview of the research results of the Štamberk castle carried out according to newly defined principles for the research, management and presentation of historical ruins, the aim of which is to support new solutions to increase the usability of the castle for tourism and to integrate the monument into the regional structures of localities with tourism potential. The castle was an important place within the territory of today's Highlands. The subject of the project, on which ITAM CAS has been collaborating with the Telčsko Microregion since 2020, is research into the history of the castle with a focus on the technological aspects of its construction, structural changes and demise. It includes the creation of a 3D model of the ruins in a landscape context. The project focuses on the history of lime production and the related inventory of geological sites. This research brings new information important not only for learning about the history of the castle or for studying analogous situations, but also for increasing the attractiveness of the monument for tourism. The paper first presents the current standards of research and management of ruins, then it deals with an outline of the research potential of Štamberk for the field of tourism with an emphasis on the history of the castle, mapping the landscape framework and identifying links to the regional environment. At the end, it summarizes the results so far that can be used to present the historical, cultural and natural wealth of the region with a specific link to tourism. Keywords: Štamberk; ruin; technological research; presentation of monuments; tourism Available at various institutes of the ASCR
Výzkum zříceniny hradu Štamberk v kontextu regionu

Příspěvek přibližuje dosavadní výsledky výzkumu hradu Štamberk realizovaného dle nově definovaných zásad pro výzkum, správu a prezentaci historických zřícenin, jehož cílem je podpořit nová řešení jak ...

Novotný, Jakub; Ramešová, Michaela
Ústav teoretické a aplikované mechaniky, 2023

Ceramic protection of anti-corrosion layers of 3-glycidyloxypropyl-triethoxysilane on steel
Pokorný, P.; Prodanović, N.; Janata, Marek; Brožek, Vlastimil
2023 - English
There are various variations on the problem of steel reinforcement bond strength in concrete. Along with geometrical considerations, corrosion performance of steels with varying chemical compositions in interaction with variable chemical compositions of concrete are crucial. One approach is to cover steel surfaces with organosilane compounds, which increases the reinforcement resistance to corrosion in both acidic and alkaline conditions but, on the other hand, may weaken the reinforcement bond strength on concrete. The issue is resolved by intentionally forming a thin-walled, highly adhering corundum layer that is highly porous and impregnated with 3-glycidyloxypropyltriethoxysilane. This procedure also includes testing the adhesion properties between the ceramic and the metal and the cement prior to conducting a corrosion test in a chloride environment. Keywords: steel; concrete; ceramics Available at various institutes of the ASCR
Ceramic protection of anti-corrosion layers of 3-glycidyloxypropyl-triethoxysilane on steel

There are various variations on the problem of steel reinforcement bond strength in concrete. Along with geometrical considerations, corrosion performance of steels with varying chemical compositions ...

Pokorný, P.; Prodanović, N.; Janata, Marek; Brožek, Vlastimil
Ústav fyziky plazmatu, 2023

Soustava frekvenčních normálů na UPT
Čížek, Martin; Hrabina, Jan; Pravdová, Lenka; Číp, Ondřej
2023 - Czech
Available at various institutes of the ASCR
Soustava frekvenčních normálů na UPT

Čížek, Martin; Hrabina, Jan; Pravdová, Lenka; Číp, Ondřej
Ústav přístrojové techniky, 2023

Plošné návrhové srážky v českých povodích
Müller, Miloslav; Kašpar, Marek; Hulec, Filip
2023 - Czech
Data o srážkové intenzitě na území Česka s horizontálním rozlišením 1 km2 a časovým krokem 10 minut, získaná adjustací radarových odhadů daty ze srážkoměrných stanic, posloužila k odvození návrhových plošných srážek v českých povodích I. až IV. řádu a v povodích útvarů povrchových vod. Při zdvojnásobení doby akumulace srážky vzroste návrhový úhrn v jednotlivých pixelech v průměru o cca 20 %. S rostoucí plochou povodí velikost návrhových úhrnů klesá, a to především v případě kratších dob akumulace. Data on rainfall intensity on the territory of the Czech Republic with a horizontal resolution of 1 km2 and a time step of 10 minutes, obtained by adjusting radar estimates with data from rain gauge stations, were used to derive design areal precipitation in the Czech river basins of 1st to 4th order and in the basins of surface water bodies. When the rainfall accumulation time is doubled, the design precipitation total in individual pixels increases by about 20% on average. The magnitude of the design totals decreases with increasing catchment area, especially for shorter accumulation periods. Keywords: design precipitation; catchment; return period Available at various institutes of the ASCR
Plošné návrhové srážky v českých povodích

Data o srážkové intenzitě na území Česka s horizontálním rozlišením 1 km2 a časovým krokem 10 minut, získaná adjustací radarových odhadů daty ze srážkoměrných stanic, posloužila k odvození návrhových ...

Müller, Miloslav; Kašpar, Marek; Hulec, Filip
Ústav fyziky atmosféry, 2023

Epidemiologické modely s agenty
Neruda, Roman
2023 - Czech
Tento příspěvek je jemným úvodem do problematiky agentních modelů a jejich aplikací v epidemiologickém modelování. Představíme agentní modely jednak z hlediska informatiky, jednak jako nástroj modelování v jiných vědních disciplínách. V příkladové studii ukážeme model s agenty a sociální sítí jejich kontaktů, který slouží pro simulaci vývoje epidemie a vlivu protiepidemických opatření. Available at various institutes of the ASCR
Epidemiologické modely s agenty

Tento příspěvek je jemným úvodem do problematiky agentních modelů a jejich aplikací v epidemiologickém modelování. Představíme agentní modely jednak z hlediska informatiky, jednak jako nástroj ...

Neruda, Roman
Ústav informatiky, 2023

Annular Impinging Jets and an Active Control of Hysteretic Effects
Devani, Yogendrasasidhar; Antošová, Zuzana; Trávníček, Zdeněk
2023 - English
An annular impinging air jet with and without flow control was studied experimentally using measurements of the wall pressure and flow velocity by the Pitot probe. To investigate flow control swirling effects, eight synthetic jets were generated from the nozzle center body. The experiments cover Reynolds numbers 4000–10,000 (evaluated from the outer exit diameter of the annular nozzle). For Re<9000, the bistability and hysteresis were identified and two different flow field patterns (A, B) were found under the same boundary conditions. For higher Re>9000, the hysteresis were not found. Keywords: annular jet; impinging jet; hysteresis Available at various institutes of the ASCR
Annular Impinging Jets and an Active Control of Hysteretic Effects

An annular impinging air jet with and without flow control was studied experimentally using measurements of the wall pressure and flow velocity by the Pitot probe. To investigate flow control swirling ...

Devani, Yogendrasasidhar; Antošová, Zuzana; Trávníček, Zdeněk
Ústav termomechaniky, 2023

About project

NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web

Send your suggestions and comments to nusl@techlib.cz

Provider

http://www.techlib.cz

Facebook

Other bases