Použitá omezení (2)  Zrušit všechna omezení
Počet nalezených dokumentů: 22065
Publikováno od do

Influence of ball material on the resulting fatigue life of thermal sprayed HVOF coatings in dynamic impact testing
Duliškovič, J.; Daniel, Josef; Houdková, Š.
2024 - anglický
Dynamic impact wear, i.e. contact between two components in the presence of high cyclic local loads, is a challenging failure mode that occurs in many mechanical applications. Many previous studies have confirmed that dynamic impact testing is suitable for evaluating the contact fatigue of thermal sprayed coatings. However, the effect of the test parameters on the resulting lifetime is unclear. The aim of this study describes the effect of the ball material used in the dynamic impact test on the resulting fatigue life of the HVOF thermal sprayed coating. Three test balls made of WC/Co alloy, Si3N4 silicon nitride and 440 C steel were chosen for this study. Dynamic impaction testing was carried out on the Cr3C2-NiCr coating, which was sprayed by HVOF on a 1.2376 high-speed steel substrate. The impact lifetime was described by the number of critical impacts, i.e. the number of impacts before coating fatigue occurs. Furthermore, the depth and volume of impact craters were measured. Using scanning electron microscopy (SEM), the surface of the impacts as well as the microstructure of the coating on the cross-section in the region of the impacts were observed. Furthermore, the mechanism of crack propagation in the coating and the microstructure of the indentor were investigated. Klíčová slova: dynamic impact test; HVOF; Cr3C2-NiCr; fatigue Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Influence of ball material on the resulting fatigue life of thermal sprayed HVOF coatings in dynamic impact testing

Dynamic impact wear, i.e. contact between two components in the presence of high cyclic local loads, is a challenging failure mode that occurs in many mechanical applications. Many previous studies ...

Duliškovič, J.; Daniel, Josef; Houdková, Š.
Ústav přístrojové techniky, 2024

Functional Tungsten-based thin films and their characterization
Košelová, Zuzana; Horáková, L.; Sobola, Dinara; Burda, Daniel; Knápek, Alexandr; Fohlerová, Z.
2024 - anglický
Anodizing is a technique by which thin oxide layers can be formed on a surface. Thin oxide layers have been found to be useful in a variety of applications, including emitters of electrons. Tungsten is still a common choice for cold field emitters in commercial microscopy applications. Its suitable quality can be further improved by thin film deposition. Not only the emission characteristic can be improved, but also the emitter operating time can be extended. Tungsten oxide is known for its excellent resistance to corrosion and chemical attack due to its stable crystal structure and strong chemical bonds between tungsten and oxygen atoms. Many techniques with different advantages and disadvantages have been used for this purpose. Anodization was chosen for this work because of the controllable uniform coverage of the material and its easy availability without the need for expensive complex equipment. The anodizing process involves applying an electrical potential to tungsten while it is immersed in an electrolyte solution. This creates a thin layer of tungsten oxide on the surface of the metal. The thickness and properties of the resulting oxide layer can be controlled by adjusting the anodization conditions, such as the electrolyte solution, voltage, and the duration of the process. In this work, H3PO4 was used as the electrolyte to test whether these tungsten oxide layers would be useful for electron emitters, for use in electron guns and other devices that require high-quality electron emitters. The properties were evaluated using appropriate techniques. In general, anodization of tungsten to form thin layers of tungsten oxide layers is a promising technique for producing high quality electron emitters. Klíčová slova: cold-field emission; thin layer deposition; tungsten oxide; resonance enhanced tunneling; anodization Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Functional Tungsten-based thin films and their characterization

Anodizing is a technique by which thin oxide layers can be formed on a surface. Thin oxide layers have been found to be useful in a variety of applications, including emitters of electrons. Tungsten ...

Košelová, Zuzana; Horáková, L.; Sobola, Dinara; Burda, Daniel; Knápek, Alexandr; Fohlerová, Z.
Ústav přístrojové techniky, 2024

Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding
Šebestová, Hana; Horník, Petr; Mika, Filip; Mikmeková, Šárka; Ambrož, Ondřej; Mrňa, Libor
2024 - anglický
Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. When the coated sheets are welded, the effect of the chemical composition of the coating must be also considered even though its thickness is only a few tens of microns. During 22MnB5+AlSi laser welding experiments, the ferrite-stabilizing elements of coating modified the weld metal microstructure. Ferrite appeared in a quenched weld metal. The rapid cooling rate accompanying welding with a focused beam limited the homogenization of the weld metal which resulted in the formation of ferritic bands in the regions rich in Si and especially in Al. On the other hand, a high level of homogenization was reached when welding with the defocused beam. The ferritic islands uniformly distributed in the weld metal were formed at 0.4 wt% and 1.6 wt% of Si and Al, respectively. The doubled heat input reduced the Al content to 0.7 wt% insufficient for the ferrite formation at still relatively high cooling rates. Predicting the distribution of ferrite in the weld metal is challenging due to its dependence on various factors, such as cooling rate and the volume of dissolved coating, which may vary with any modifications made to the welding parameters. Klíčová slova: laser welding; high-strength steel; microstructure; heat input; ferrite stabilization Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding

Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. ...

Šebestová, Hana; Horník, Petr; Mika, Filip; Mikmeková, Šárka; Ambrož, Ondřej; Mrňa, Libor
Ústav přístrojové techniky, 2024

Polyfunkční budova
Almeida, Adérito Cláudio Lopes de; Jelínek, Petr; Struhala, Karel
2023 - anglický
Plné texty jsou dostupné v digitálním repozitáři NUŠL
Polyfunkční budova

Almeida, Adérito Cláudio Lopes de; Jelínek, Petr; Struhala, Karel
Vysoké učení technické v Brně, 2023

Modifikace vlastností alkalicky aktivovaných aluminosilikátů polymerními přísadami
Mikhailova, Olesia; Bílek, Vlastimil; Vejmelková,, Eva; Žižková, Nikol; Rovnaník, Pavel
2023 - anglický
V současné době se v betonářském průmyslu ve velké míře používá portlandský cement (PC), jehož výroba má značný dopad na životní prostředí a zároveň se jedná o neudržitelný proces. Snahy o ekologičtější stavebnictví zahrnují využití několika aluminosilikátů, které mohou být buď odpadními produkty získanými z jiných průmyslových výrob, jako je granulovaná vysokopecní struska, popílek a křemičitá dýmka, nebo materiály pocházející z energeticky méně náročných průmyslových procesů, jako je metakaolin. Použití těchto materiálů při výrobě stavebních materiálů rovněž přispívá ke snížení výrobních nákladů. Aktivace aluminosilikátových materiálů alkalickými aktivátory vede k získání vysoce pevných materiálů, které lze považovat za alternativu běžného PC. Navzdory mnoha výhodám alkalicky aktivovaných aluminosilikátů (AAA) existuje zásadní nevýhoda, která se týká výrazného autogenního smršťování a smršťování při vysoušení, k němuž může docházet během tuhnutí materiálu. Tento jev vede k mikrotrhlinám a zhoršení mechanických lomových vlastností. Polymerní příměsi mohou modifikovat vlastnosti čerstvého a vytvrzeného materiálu AAA a překonat výše uvedené problémy. Tato disertační práce se zabývá vlivem polymerních přísad v různých hmotnostních množstvích aluminosilikátového pojiva na snižování smrštění a křehkosti a na zvýšení lomové houževnatosti. Jako polymerní příměsi byly vybrány polyetylen glykol (PEG), polypropylen glykol (PPG) a různé typy komerčních polymerů z řady dispergovatelných polymerních prášků Vinnapas®. Jejich vliv na vlastnosti získaných materiálů byl porovnáván s vlivem práškového přípravku proti smrštění Peramin SRA 40. Vzorky byly testovány na pevnost v ohybu a tlaku a jejich mikrostruktura byla zkoumána pomocí rtuťové porozimetrie a skenovací elektronové mikroskopie. Jedna z kapitol práce se zabývá studiem různých charakterizačních technik vzniku hlavních reakčních produktů v alkalicky aktivované strusce, jako jsou RTG difrakční analýza, Fourierovou tran Currently, the concrete industry utilizes Portland cement (PC) widely, whose production has a significant environmental impact, while it is also a non-sustainable process. Efforts towards a greener building industry involve employing several aluminosilicate materials that can be either by-products obtained from other industrial activities, such as granulated blast furnace slag, silica fume, and fly ash, or materials derived from less energy-intensive industrial processes, such as metakaolin. Using these materials in the preparation of building materials also contributes to reduced production costs. Activation of aluminosilicate materials by alkaline activators leads to high-strength materials that can be considered an alternative to ordinary Portland cement (OPC). Despite the numerous advantages of alkali-activated aluminosilicates (AAA), a major drawback is the significant autogenous and drying shrinkage that might occur during the material’s hardening. This phenomenon leads to microcracking and deterioration of mechanical fracture properties. Polymer admixtures can modify the properties of the fresh and hardened AAA material and overcome the abovementioned problems. This thesis investigates the influence of polymer admixtures, in different amounts by weight of the aluminosilicate binder, on reducing shrinkage and fragility and increasing fracture toughness. Polyethylene glycol (PEG), Polypropylene glycol (PPG), and different types of commercial polymers of the Vinnapas® - family of dispersible polymer powders were selected as polymer admixtures. Their effect on the properties of the obtained materials was compared with that of powder shrinkage reducer Peramin SRA 40. The specimens were tested for flexural and compressive strength, and their microstructure was investigated employing mercury intrusion porosimetry and scanning electron microscopy One of the chapters of the thesis deals with the study of different analytical techniques for the characterization Klíčová slova: Alkali activated materials; geopolymers; slag; metakaolin; polymer admixtures; Alkalicky aktivované materiály; geopolymery; struska; metakaolin; polymerní přísady Plné texty jsou dostupné v digitálním repozitáři NUŠL
Modifikace vlastností alkalicky aktivovaných aluminosilikátů polymerními přísadami

V současné době se v betonářském průmyslu ve velké míře používá portlandský cement (PC), jehož výroba má značný dopad na životní prostředí a zároveň se jedná o neudržitelný proces. Snahy o ...

Mikhailova, Olesia; Bílek, Vlastimil; Vejmelková,, Eva; Žižková, Nikol; Rovnaník, Pavel
Vysoké učení technické v Brně, 2023

2TDK Railway, profile P18. Datings. Final Report.
Bosák, Pavel; Zupan Hajna, N.; Hercman, H.; Horáček, I.; Kdýr, Šimon; Kogovšek, B.
2023 - anglický
Samples for datings were taken in the railway construction (2TDK) near village of Divača, Classical Karst on October 12, 2021: (1) vertebrate bones in cave 2TDK – 002 at the profile P18, cave entrance appeared during the construction operations on cleaned karst surface in a wall of karst depression. Samples of mammal bones and gastropods were collected in situ on cave bottom, and (2) pieces of speleothems occurring in non in situ position on artificially planated surface near the cave opening were collected. U-series: no numerical date was obtained as geochemistry of sample indicate open system, probably due to recrystallization of sample in soil cover. Paleomagnetism: The transition of N- and R-polarized samples cannot be identified more precisely as U-series radiometric dating yielded no numerical results. The transition easily can represent Brunhes/Matuyama boundary (at 773 ka) as well as any of older such transitions (e. g., base of Jaramillo, base of Olduvai). In any case the speleothem grew in a closed cave space with roof, probably as flowstone (inclusion of red soils above the base) and later as baldachin on eroded allogenic fill of the paleocave. Vertebrate paleontology: bone remains of small and larger vertebrates represent subrecent to Holocene species. Sorex alpinus represents the species quite rare in fossil record, but recetly limited to variegated woodland habitats with high surface humidity. A chamois Rupicapra rupicapra represents a resident species present in Slovenia throughout all stages of a glacial cycle, recently restricted to mountain habitats. Klíčová slova: Divača Karst; unroofed cave; speleothem; U-Th dating; paleomagnetism; zoopaleontology Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
2TDK Railway, profile P18. Datings. Final Report.

Samples for datings were taken in the railway construction (2TDK) near village of Divača, Classical Karst on October 12, 2021: (1) vertebrate bones in cave 2TDK – 002 at the profile P18, cave entrance ...

Bosák, Pavel; Zupan Hajna, N.; Hercman, H.; Horáček, I.; Kdýr, Šimon; Kogovšek, B.
Geologický ústav, 2023

Field Programmable Neural Networks odolná proti poruchám
Krčma, Martin; Kordík, Pavel; Stopjaková, Viera; Drábek, Vladimír
2023 - anglický
Tato práce se zaměřuje na koncept Field Programmable Neural Networks jehož cílem je učinit implementaci umělých neuronových sítí v hradlových polích méně náročnou jejich prostředky. Za tímto účelem práce koncept rozvíjí a představuje několik jeho různých typů jež se vyznačují různými poměry mezi spotřebou zdrojů hradlových polí a přesností s jakou aproximují původní neuronovou síť jíž implementují. Teze díle rozšiřuje koncept o metody zabezpečení proti poruchám s využitím redundance a také bez ní. This thesis focuses on the Field Programmable Neural Networks concept intended to make implementation of neural networks in FPGAs less resource demanding. The thesis introduces and discusses several types of Field Programmable Neural Networks which provide different trad-offs between the resource consumption and the accuracy of the implemented neural network approximation. This thesis also introduces and discusses methods of hardening the Field Programmable Neural Networks against faults with and without redundancy. Klíčová slova: Field Programmable Neural Networks; fault tolerance; neural networks; FPGAs; Field Programmable Neural Networks; odolnost proti poruchám; neuronové sítě; FPGA Plné texty jsou dostupné v digitálním repozitáři NUŠL
Field Programmable Neural Networks odolná proti poruchám

Tato práce se zaměřuje na koncept Field Programmable Neural Networks jehož cílem je učinit implementaci umělých neuronových sítí v hradlových polích méně náročnou jejich prostředky. Za tímto účelem ...

Krčma, Martin; Kordík, Pavel; Stopjaková, Viera; Drábek, Vladimír
Vysoké učení technické v Brně, 2023

Room temperature ethanol detection using carbon materials
Kočí, Michal
2023 - anglický
Allotropic forms of carbon, in particular graphene oxide (GO) or nanocrystalline diamond (NCD), attracted the attention of many research groups due to their unique electronic structures and extraordinary physical and chemical properties, preferable for many different applications, including sensor devices. This work focuses on responses of various sensing layers (NCD with hydrogen termination (H-NCD), graphene oxide (GO), reduced graphene oxide (rGO), thiol-functionalized graphene oxide (GO-SH) and their hybrid structures to ethanol vapor with concentrations up to 100 ppm in synthetic air at room temperature. The measured parameters of the tested sensors, especially stability, reproducibility and regeneration, are compared and critically evaluated. The high sensitivity of tested sensors achieved at room temperature makes them very promising for monitoring ethanol vapor as well as other volatile substances (e.g., isopropyl-alcohol or acetone). Klíčová slova: gas sensor; nanocrystalline diamond (NCD); graphene oxide (GO); reduced graphene oxide (rGO); thiol-functionalized graphene oxide (GO-SH) Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Room temperature ethanol detection using carbon materials

Allotropic forms of carbon, in particular graphene oxide (GO) or nanocrystalline diamond (NCD), attracted the attention of many research groups due to their unique electronic structures and ...

Kočí, Michal
Fyzikální ústav, 2023

Strukturální studie extracelulárních domén adheze G protein-spojeného receptoru ADGRG4
Strnadová, Martina; Márová, Ivana; Mravec, Filip
2023 - anglický
Bunková komunikácia je schopnosť buniek príjmať, vysielať a spracovávať signály zo svojho okolia. Môžeme teda hovoriť o komunikácii medzi bunkami a orgamizmom. Extracelulárne stimuly spúšťajú signál, ktorý interaguje s receptormi na bunkovom povrchu, čo má za následok aktiváciu intracelulárnych signálnych proteínov. Tieto proteíny sú rozdelené do viacerých rodín podľa ich špecifickej sekvencie, domén ktoré obsahujú, alebo ligandov, s ktorými interagujú. Jednou z týchto rodín je práve receptorová rodina adhezívnych receptorov spojených s G proteínom (aGPCR), ktorá obsahuje 33 členov. Najnovšie štúdie naznačujú, že fungujú z veľkej časti ako mechanoreceptory; avšak, pre niektorých členov boli identifikované aj ligandy pre ich aktiváciu. V porovnaní s inými GPCR sa táto rodina vyznačuje relatívne dlhou extracelulárnou oblasťou (ECR), ktorá obsahuje súbor rozličných štruktúrnych domén a motívov. ADGRG4 (GPR112) predstavuje jeden z najväčších aGPCR s dĺžkou reťazca väčšou ako 3000 aminokyselín (aa). Väčšina jeho reťazca aa sa nachádza v extracelulárnom priestore (viac ako 2500 aa). Je známe, že ADGRG4 je špecificky exprimovaný v enterochromafinných bunkách umiestnených v epiteli ľudského tenkého čreva. Tieto enteroendokrinné bunky sú zodpovedné za produkciu a sekréciu serotonínu a reagujú na chemické a mechanické podnety. K dnešnému dňu však fyziologická funkcia ADGRG4 v týchto bunkách zostáva neznáma. Cieľ tejto práce bol rozdelený na dve časti. V prvej časti bola snaha o poskytnutie štruktúrnych informácií o obrovskej extracelulárnej oblasti ADGRG4. ECR bola rozdelená na viacero častí pre lepšie skúmanie. Následne boli vzorky exprimované v ľudských embryonálnych obličkových bunkách 293 (HEK293S bunky). Výsledné proteínové štruktúry boli purifikované viacerými technikami. Pre zvýšenie možnosti kryštalizácie, bol purifikovaný proteín deglykozylovaný a až potom podrobený na kryštalizačné pokusy. Druhá časť sa zaoberala analýzou NTF-konštruktov, dobre preskúmaných ADGRs. Tieto konštrukty neobsahovali C-terminálny koniec (CTF), iba N-terminálnu časť (NTF). Desať rôznych proteínov bolo úspešne naklonovaných a expresovaných v HEK293T bunkách. Na vyhodnotenie výsledkov oligomerného stavu vzoriek z prvej aj druhej časti boli použité techniky Native PAGE a dynamický rozptyl svetla (DLS). Ako kontrola autoproteolýzy, ktorá je typickým znakom aGPCR, sa využili rozličné techniky Western blotting (WB). Metóda nano-diferenciačná skenovacia fluorescencia (DSF) sa využila na stanovenie pripravených konštruktov a na nájdenie optimálnych podmienok pre roztoky, ktoré sa v práci používali. Výsledky z prvej časti ukazujú za akých podmienok dokážeme nami vytvorený konštruk podrobiť kryštalizácii a následne ďalej pokračovať v jeho výskume. Druhá časť nám ukázala, ktoré nami klonované konštrukty sa dokážu stabilne expresovať v HEK293T bunkách. Na základe získaných parametrov z prvej a druhej časti dokáže výskum v tejto oblasti rozšíriť a do buducnosti získať dôležité informácie ohľadom týchto pozoruhodných receptorov. The aim of this thesis was to provide structural information on the huge extracellular region (ECR) of ADGRG4 that allows hypothesis of the function of the receptor. Therefore, the ECR was dissected into smaller, likely independently folded subunits. Subsequently, these samples were recombinantly expressed in human embryonic kidney 293 cells (HEK293S cells). These protein constructs were purified to allow for subsequent biophysical characterization. To increase the possibility of protein crystallisation, the purified protein was deglycosylated and then subjected to crystallisation trials. The second part of this thesis dealt with the analysis of the construct that contained the NTF part (the CTF was lacking), of well-established ADGRs. Ten different constructs were successfully cloned and expressed in HEK293T cells. Native PAGE and Dynamic Light Scattering (DLS) techniques were used to evaluate the results of the oligomeric state of the samples from both parts. As a control for autoproteolysis, which is a typical feature of aGPCR, various WB techniques were used. The Nano-Differential Scanner Fluorescence (DSF method was used to determine the prepared constructs and to find the optimal conditions for the buffers used in the thesis. The results of the first part show under which conditions the crystallisation trials were the most suitable that can be repeated and optimized further in the research. The second part showed which cloned constructs were able to be expressed in cells. Based on the parameters obtained from the first and second parts, research in this area can continue and, in the future, we can obtain important information about these remarkable receptors. Klíčová slova: aGPCR; ADGRG4; NTF-constructs; molecular cloning; Dynamic Light Scattering; Nano-Differential Scanner Fluorimetry; protein crystallisation; aGPCR; ADGRG4; NTF-konštrukty; molekulárne klonovanie; dynamický rozptyl svetla; nano.diferenciačná skenovacia fluorescencia; proteínová kryštalizácia Plné texty jsou dostupné v digitálním repozitáři NUŠL
Strukturální studie extracelulárních domén adheze G protein-spojeného receptoru ADGRG4

Bunková komunikácia je schopnosť buniek príjmať, vysielať a spracovávať signály zo svojho okolia. Môžeme teda hovoriť o komunikácii medzi bunkami a orgamizmom. Extracelulárne stimuly spúšťajú signál, ...

Strnadová, Martina; Márová, Ivana; Mravec, Filip
Vysoké učení technické v Brně, 2023

Experimental investigation and numerical modelling of top of rail products
Kvarda, Daniel; prof.Roger Lewis; Meierhofer, Alexander; Hartl, Martin
2023 - anglický
Tato disertační práce se zabývá experimentálním a numerickým studiem maziv pro temeno kolejnice. Tyto maziva se používají ke snížení opotřebení, hluku a zlepšení energetické účinnosti kontaktu kola a kolejnice. V posledních dvou desetiletích byl proveden rozsáhlý experimentální výzkum týkající se použití maziv pro temeno kolejnice. Avšak velmi málo výzkumu bylo zaměřeno na základní mechanismy těchto produktů, zejména na problémy s nízkou adhezí. Aplikace matematických modelů v této oblasti také nebyla dosud zkoumána. Cílem této práce je pomocí matematického modelu vysvětlit třecí chování a problémy s nízkou adhezí maziv pro temeno kolejnice. Model předpokládá jak tření vznikající interakcí nerovností pevných látek, tak separaci mazacím filmem. Validace tohoto modelu byla provedena na experimentálním tribometru se schopností měřit tloušťku filmu pro ověření přesné predikce separace povrchu. Komerční tribometr byl použit ke zkoumání vlivu jednotlivých složek v mazivu pro temeno kolejnice na bázi oleje. Sada reologických testů v kombinaci s modelem ukázala, že pevné částice měly velmi malý vliv na zvýšení adheze po aplikaci. Následně byly testovány různé typy maziv pro temeno kolejnice pomocí vysokotlakého torzního zařízení. Mezný režim tření těchto látek byl hodnocen představeným modelem. Bylo zjištěno, že pozitivní třecí vlastnosti, které by tyto produkty měly poskytovat, jsou výsledkem velké skluzové vzdálenosti, která mění složení třecí vrstvy. Nízký koeficient tření v důsledku nadměrné aplikace se vyskytl při stejném aplikovaném množství u všech testovaných látek. Tato diplomová práce představuje původní výzkum rozšiřující znalosti o produktech pro temeno kolejnice. This dissertation thesis deals with experimental and numerical study of top or rail products. These products are used to reduce wear, noise and improve energy efficiency of wheel and rail contact. In the last two decades, extensive experimental research has been conducted on the use of top of rail products. However, very little research has focused on the fundamental mechanisms of these products, especially causes of low adhesion. Application of mathematical models to this field was also not yet examined. The aim of this thesis is to explain the frictional behaviour and low adhesion conditions of the top of rail products with the use of a mathematical model. The model assumes both friction arising from solid asperity interaction and separation by a fluid film. The validation of this model was carried out on an experimental tribometer with the ability to measure film thickness to validate the accurate prediction of surface separation. A commercial tribometer was used to investigate the influence of individual components in oil-based top of rail product on the coefficient of adhesion. A set of rheological tests in combination with the model showed that the solid particles had very little effect in increasing adhesion after application. Subsequently, different types of top of rail products were tested using a high pressure torsion device. The boundary friction of these substances was evaluated by the model. The positive frictional characteristics that these products should provide are found to be a result of sliding friction changing the composition of the interfacial layer. In addition, the low coefficient of friction due to overapplication occurred at the same amount applied for all tested substances. This thesis presents original research expanding on the knowledge of top of rail products. Klíčová slova: Wheel-rail contact; Friction management; Top of rail products; Numerical model; Tribology; Kontakt kolo-kolejnice; Řízení tření; Maziva pro kolejový svršek; Numerický model; Tribologie Plné texty jsou dostupné v digitálním repozitáři NUŠL
Experimental investigation and numerical modelling of top of rail products

Tato disertační práce se zabývá experimentálním a numerickým studiem maziv pro temeno kolejnice. Tyto maziva se používají ke snížení opotřebení, hluku a zlepšení energetické účinnosti kontaktu kola a ...

Kvarda, Daniel; prof.Roger Lewis; Meierhofer, Alexander; Hartl, Martin
Vysoké učení technické v Brně, 2023

O službě

NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.

Vaše náměty a připomínky posílejte na email nusl@techlib.cz

Provozovatel

http://www.techlib.cz

Facebook

Zahraniční báze