Number of found documents: 220
Published from to

Effect of the eta eta channel and interference phenomena in the two-pion transitions of charmonia and bottomonia
Surovtsev, Yu .S.; Bydžovský, Petr; Gutsche, T.; Kaminski, R.; Lyubovitskij, V. E.; Nagy, M.
2017 - English
The basic shape of di-pion mass spectra in the two-pion transitions of both charmonia and bottomonia states is explained by a unified mechanism based on contributions of the pi pi, K (K) over bar, and eta eta coupled channels including their interference. The role of the individual f(0) resonances in shaping the di-pion mass distributions in the charmonia and bottomonia decays is considered. Keywords: resonance; charmonia; bottomonia Available at various institutes of the ASCR
Effect of the eta eta channel and interference phenomena in the two-pion transitions of charmonia and bottomonia

The basic shape of di-pion mass spectra in the two-pion transitions of both charmonia and bottomonia states is explained by a unified mechanism based on contributions of the pi pi, K (K) over bar, and ...

Surovtsev, Yu .S.; Bydžovský, Petr; Gutsche, T.; Kaminski, R.; Lyubovitskij, V. E.; Nagy, M.
Ústav jaderné fyziky, 2017

Fragmentation from heavy ion beams in HIMAC BIO room calculated with PHITS and measured with Liulin
Ploc, Ondřej; Dachev, T.; Uchihori, Y.; Kitamura, H.; Sihver, L.
2017 - English
The Heavy Ion Medical Accelerator in Chiba (HIMAC), at the National Institutes for Quantum and Radiological Science and Technology, is not only an excellent cancer-treatment facility but also a facility to perform experiments related to radiation therapy, space radiation protection and basic nuclear physics. HIMAC BIO is an irradiation room used for experiments related to both radiobiology and physics. When performing such experiments, it is essential to know the experimental setup, as well as the beam characteristics, in details. The advantage of HIMAC BIO is that both narrow and broad parallel heavy ion beams (up to. 10 cm), with flat circular profile at the isocenter, can be used for experiments. Such beam is obtained by using scatterers, ridge filters, beam degraders, etc., similar to what is used during radiation therapy. However, these components decrease the energies of the primary beams and are sources of secondary particles. To be able to draw correct conclusions from the experimental results, and to be able to compare the measurements with simulations, it is crucial to know the real energy of the primary ions and the detailed beam composition at the location of the biological samples and the physical detectors. The energies of the primary ions are calculated from Bragg curve measurements with a Markus ionization chamber before each experiment. However, the exact beam composition including the fluence and energies of the secondary fragments and neutrons are usually unknown. The purpose ofdetailed information about the components in the beam line at the HIMAC BIO room to facilitate accurate particle and heavy ion transport simulations of the beam characteristics. The main sources of secondary particles have been investigated, and the beam composition was calculated with the 3-dimensional general purpose Monte Carlo this paper is to provide PHITS and compared with measurements using a Liulin exposed to various monoenergetic and SOBP heavy ion beams. Keywords: HIMAC BIO; cosmic rays; dosimetry Available at various institutes of the ASCR
Fragmentation from heavy ion beams in HIMAC BIO room calculated with PHITS and measured with Liulin

The Heavy Ion Medical Accelerator in Chiba (HIMAC), at the National Institutes for Quantum and Radiological Science and Technology, is not only an excellent cancer-treatment facility but also a ...

Ploc, Ondřej; Dachev, T.; Uchihori, Y.; Kitamura, H.; Sihver, L.
Ústav jaderné fyziky, 2017

Proton and deuteron activation measurements at the NPI and future plans in SPIRAL2/NFS
Šimečková, Eva; Bém, Pavel; Mrázek, Jaromír; Štefánik, Milan; Běhal, Radomír; Glagolev, Vadim
2017 - English
The proton- and deuteron-induced reactions are of a great interest for the assessment of induced radioactivity of accelerator components, target and beam stoppers as well as isotope production for medicine. In the present work, the deuteron-induced reaction cross sections on zinc were investigated by stacked-foil activation technique with deuteron beam of 20 MeV energy from the cyclotron U-120M of NPI CAS ež. Also the proton activation cross section measurement of iron is presented. The comparison of present results to data of other authors and to predictions of evaluated data libraries is discussed. The investigation shall continue for higher proton and deuteron energy interval 20-35 MeV at SPIRAL2/NFS facility using a charged particle irradiation chamber with pneumatic transport system to measure isotopes and isomers with half-lives in minutes-regions. Keywords: SPIRAL2/NFS; CANAM accelerators; cross section Available at various institutes of the ASCR
Proton and deuteron activation measurements at the NPI and future plans in SPIRAL2/NFS

The proton- and deuteron-induced reactions are of a great interest for the assessment of induced radioactivity of accelerator components, target and beam stoppers as well as isotope production for ...

Šimečková, Eva; Bém, Pavel; Mrázek, Jaromír; Štefánik, Milan; Běhal, Radomír; Glagolev, Vadim
Ústav jaderné fyziky, 2017

Position-Sensitive Coincidence Detection of Nuclear Reaction Products at the Prague Van-de-Graaff Accelerator
Granja, Carlos; Kraus, V.; Pugatch, V.; Kohout, Z.
2017 - English
In low-energy nuclear reactions of astrophysical interest or fusion studies the spatial-and time-correlated detection of two and more reaction products can be a valuable tool in studies of reaction mechanisms, resolving reaction channels and measuring angular distributions of reaction products. For this purpose we constructed a configurable array of position-sensitive detectors based on the hybrid semiconductor pixel detector Timepix. Additional analog-signal electronics provide self-trigger together with extended multi-device control and synchronized readout electronics by a customized control and coincidence unit. The instrumentation, developed and used for detection of fission fragments in spontaneous and neutron induced fission as well as in charged particle detection in neutron induced reactions, is being implemented for low-energy light-ion induced nuclear reactions. Application and demonstration of the technique with two Timepix detectors on p+p elastic scattering at the Van-de-Graaff (VdG) accelerator in Prague is given. Keywords: Van-de-Graaff; Timepix Available at various institutes of the ASCR
Position-Sensitive Coincidence Detection of Nuclear Reaction Products at the Prague Van-de-Graaff Accelerator

In low-energy nuclear reactions of astrophysical interest or fusion studies the spatial-and time-correlated detection of two and more reaction products can be a valuable tool in studies of reaction ...

Granja, Carlos; Kraus, V.; Pugatch, V.; Kohout, Z.
Ústav jaderné fyziky, 2017

Numerical modeling of surface elastic wave scattering in polycrystalline materials
Grabec, Tomáš; Ryzy, M.; Verres, I. A.
2017 - English
Grain-boundary scattering of acoustic waves in polycrystalline materials is studied with analytical and numerical methods in the presented paper. In particular, the attenuation of Surface Acoustic Waves (SAWs) propagating through a polycrystalline microstructure is investigated. A three dimensional timedomain finite-element method (FEM) is utilized for the numerical simulation, whereby the granular microstructure is modeled by Voronoi tessellation. The resulting frequency-dependent attenuation coefficients are compared to an explicit analytical model. Keywords: grain boundary scattering; elastic wave; numerical modeling; polycrystalline material Available at various institutes of the ASCR
Numerical modeling of surface elastic wave scattering in polycrystalline materials

Grain-boundary scattering of acoustic waves in polycrystalline materials is studied with analytical and numerical methods in the presented paper. In particular, the attenuation of Surface Acoustic ...

Grabec, Tomáš; Ryzy, M.; Verres, I. A.
Ústav jaderné fyziky, 2017

Residual stress determination by neutron diffraction in low-carbon steel wires with accumulated shear deformation
Rogante, M.; Mikula, Pavol; Strunz, Pavel; Zavdoveev, A.
2017 - English
Modern methods of severe plastic deformation (SPD) currently allow obtaining the ultrafine-grained (UFG) structure nearly in any material. In the manufacturing process of wire with UFG structure, a main restriction is the continuous drawing scheme in which this process occurs, thus it is important to consider the factors affecting the drawing efficiency. Despite the data on SPD steels such as strength, plasticity and conductivity, obtained by classical methodologies, further investigations are needed: a key information is the residual stresses (RS) status, and RS determination is an essential issue to improve knowledge of SPD effects. In this work, 15 wires samples made of low-alloyed quality structural steel Grade 08G2S GOST 1050 with accumulated shear deformation - as result of rolling with shear of the metal ingot and conventional wire drawing - have been investigated by neutron diffraction (ND). Results provide substantial data helping to evaluate the effect of shear deformation on RS of the considered steel, as well as additional support to complement the information already achieved by using the other characterization methodologies. Knowledge of the RS status can help developing a lowcarbon wire drawing technology with needed manufacturability and efficiency, playing a decisive role in the debugging of material selection and engineering design requirements. Keywords: Residual stresses; Neutron diffraction; Steel Available at various institutes of the ASCR
Residual stress determination by neutron diffraction in low-carbon steel wires with accumulated shear deformation

Modern methods of severe plastic deformation (SPD) currently allow obtaining the ultrafine-grained (UFG) structure nearly in any material. In the manufacturing process of wire with UFG structure, a ...

Rogante, M.; Mikula, Pavol; Strunz, Pavel; Zavdoveev, A.
Ústav jaderné fyziky, 2017

Modifikace materiálů pro optiku, elektroniku a spintroniku iontovým svazkem – iontová implantace pomocí urychlovačů nebo laserem indukovaného plazmatu
Macková, Anna
2016 - Czech
Ion beam modification offers a broad field of the creating the new functional materials and nano-structures for optics, electronics, spintronics and other material branches. Using ions produced by ion accelerators or implanters\nmeans the usage of the monoenergetic beams for precise doped layer, nano-particles or cluster creation by varying the ion implantation specie versus matrix combination together with the implantation energy, ion flux etc. Recently\nappears the multienergetic ion implantation which is realized by using of the intense laser shot generating plasma from the specially designed targets, where the ions are accelerated and can be then implanted into the various\nmaterials. This contribution will present an overview and comparison of different ion beam modification techniques, plasma ion implantation will be also mentioned. Keywords: modification; materials; ion implantation Available at various institutes of the ASCR
Modifikace materiálů pro optiku, elektroniku a spintroniku iontovým svazkem – iontová implantace pomocí urychlovačů nebo laserem indukovaného plazmatu

Ion beam modification offers a broad field of the creating the new functional materials and nano-structures for optics, electronics, spintronics and other material branches. Using ions produced by ion ...

Macková, Anna
Ústav jaderné fyziky, 2016

Calibration and Exact Characterization of Aerosol Deposit colected by SDI Impactor
Havránek, Vladimír
2016 - English
Ion beam analytical methods as PIXE (Particle induced X-ray emission), PIGE (Particle induced gamma-ray emission) and RBS (Rutherford backscattering spectrometry) are frequently used for elemental analysis of different types of atmospheric aerosol samples in a form of aerosol deposits on thin plastic filters or foils (Alfassi and Peisach, 1991, Johansson and Campbell, 1988). An ideal sample for analysis is thin homogeneous aerosol deposit with known deposit area. However in practice such samples are rare. They are often thick (more than limit for thin target approximation i.e. larger then few hundred micrograms per square centimetres), of irregular shape and unknown deposit area. In such conditions all obtained elemental mass results should be corrected for apparent deposit thickness, deposit homogeneity and effective deposit area. Keywords: atmospheric aerosols; PIXE; RBS; calibration; elemental concentration Available at various institutes of the ASCR
Calibration and Exact Characterization of Aerosol Deposit colected by SDI Impactor

Ion beam analytical methods as PIXE (Particle induced X-ray emission), PIGE (Particle induced gamma-ray emission) and RBS (Rutherford backscattering spectrometry) are frequently used for elemental ...

Havránek, Vladimír
Ústav jaderné fyziky, 2016

Vliv kryogenního mletí na homogenitu jódu v NIST SRM1548a Typical Diet
Kameník, Jan; Kučera, Jan
2016 - Czech
The reference material NIST SRM 1548a Typical Diet has a certified iodine mass fraction of 0.759±0.103 mg kg-1. The expanded uncertainty is rather large (relative value 13.6 %), thus the material does not provide strict requirements for quality control results. Milling of NIST SRM 1548a at the temperature of liquid nitrogen yielded free-flowing material. Iodine mass fraction in the original and cryo-ground materials was determined by epithermal neutron activation analysis (ENAA) and radiochemical neutron activation analysis (RNAA). The average and standard deviation from both methods was 0.73±0.03 mg kg-1 (20 values). The determined mass fraction was in a close agreement with the certified value of NIST SRM 1548a, thus iodine total content was not influenced by the milling procedure. In comparison to iodine mass fraction determined in the original NIST SRM 1548a 0.72±0.07 mg kg-1 (average ± standard deviation, 14 values), the standard deviation for cryo-ground material was considerably lower. The prepared quality control material sets up more stringent requirements on the validation and quality control procedures of the measurement of iodine mass fraction in such a composite food matrices. We believe that the iodine random inhomogeneity in the original NIST SRM 1548a is due to insufficient mixing of some iodine-rich component in the complex food matrices. Milling at the temperature of liquid nitrogen offers an effective option for production of future reference materials of this kind. The reference material NIST SRM 1548a Typical Diet has a certified iodine mass fraction of 0.759±0.103 mg kg-1. The expanded uncertainty is rather large (relative value 13.6 %), thus the material does not provide strict requirements for quality control results. Milling of NIST SRM 1548a at the temperature of liquid nitrogen yielded free-flowing material. Iodine mass fraction in the original and cryo-ground materials was determined by epithermal neutron activation analysis (ENAA) and radiochemical neutron activation analysis (RNAA). The average and standard deviation from both methods was 0.73±0.03 mg kg-1 (20 values). The determined mass fraction was in a close agreement with the certified value of NIST SRM 1548a, thus iodine total content was not influenced by the milling procedure. In comparison to iodine mass fraction determined in the original NIST SRM 1548a 0.72±0.07 mg kg-1 (average ± standard deviation, 14 values), the standard deviation for cryo-ground material was considerably lower. The prepared quality control material sets up more stringent requirements on the validation and quality control procedures of the measurement of iodine mass fraction in such a composite food matrices. We believe that the iodine random inhomogeneity in the original NIST SRM 1548a is due to insufficient mixing of some iodine-rich component in the complex food matrices. Milling at the temperature of liquid nitrogen offers an effective option for production of future reference materials of this kind. Keywords: SRM1548a Typical Diet; epithermal neutron activation analysis; radiochemical neutron activation analysis Available at various institutes of the ASCR
Vliv kryogenního mletí na homogenitu jódu v NIST SRM1548a Typical Diet

The reference material NIST SRM 1548a Typical Diet has a certified iodine mass fraction of 0.759±0.103 mg kg-1. The expanded uncertainty is rather large (relative value 13.6 %), thus the material does ...

Kameník, Jan; Kučera, Jan
Ústav jaderné fyziky, 2016

Study of fully automated analyzing system for the study of low-dose radiation effects on cellular radiobiology
Nagasaki, Y.; Matuo, Y.; Pachnerová Brabcová, Kateřina; Yasuda, N.
2016 - English
Study of fully automated analyzing system for the study of low-dose radiation effects on cellular radiobiology (poster) Keywords: storage facility; dosimetry; irradiation Available at various institutes of the ASCR
Study of fully automated analyzing system for the study of low-dose radiation effects on cellular radiobiology

Study of fully automated analyzing system for the study of low-dose radiation effects on cellular radiobiology (poster)

Nagasaki, Y.; Matuo, Y.; Pachnerová Brabcová, Kateřina; Yasuda, N.
Ústav jaderné fyziky, 2016

About project

NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web

Send your suggestions and comments to nusl@techlib.cz

Provider

http://www.techlib.cz

Facebook

Other bases