Number of found documents: 988
Published from to

Applying a two degree of freedom model for drive-by identification
Bayer, Jan
2024 - English
A new concept of drive-by identification is examined applying the analogy with a Two Degree Of Freedom (DOF) system where the bridge is considered the ground-supported spring-mass and the moving spring-mass the second DOF. The response of the moving spring-mass is simulated on a bridge model using different road profiles and compared to parameters of the corresponding two DOF system. The focus is the spectral shift that can be observed on the moving spring-mass during its passage along the bridge and could possibly be applied for drive-by identification. The accuracy mainly depends on the relation of the moving spring-mass to the bridge mass and the relation between the natural frequency of the spring-mass and those of the bridge. The simulations showed that road profile can significantly reduce the accuracy of identified results, which imposes limits on practical applications. Keywords: drive-by identification; structural health monitoring; finite element analysis; road roughness; two DOF system Available in digital repository of the ASCR
Applying a two degree of freedom model for drive-by identification

A new concept of drive-by identification is examined applying the analogy with a Two Degree Of Freedom (DOF) system where the bridge is considered the ground-supported spring-mass and the moving ...

Bayer, Jan
Ústav teoretické a aplikované mechaniky, 2024

Solution methods for an aeroelastic problem with combined harmonic and stochastic excitation
Fischer, Cyril; Náprstek, Jiří
2024 - English
Assessing responses in slender engineering structures facing both deterministic harmonic and stochastic excitation is often based on an approximation by the single-degree-of-freedom van der Pol-type nonlinear model. Determining the response probability density function involves solving the Fokker-Planck equation, which is generally a challenging task. Hence, semi-analytical and numerical methods come into play. This contribution reviews several possible techniques and spotlights the exponential-polynomial-closure method. The shown results are limited, as the paper reflects an early stage of the relevant research direction. Keywords: Fokker-Planck equation; stochastic averaging; numerical solution; Galerkin approximation; van der Pol-type oscillator; partial amplitudes; exponential-polynomial-closure method Available in digital repository of the ASCR
Solution methods for an aeroelastic problem with combined harmonic and stochastic excitation

Assessing responses in slender engineering structures facing both deterministic harmonic and stochastic excitation is often based on an approximation by the single-degree-of-freedom van der Pol-type ...

Fischer, Cyril; Náprstek, Jiří
Ústav teoretické a aplikované mechaniky, 2024

Galloping of insulated bundled overhead line simplified analysis
Hračov, Stanislav; Macháček, Michael
2024 - English
Our paper provides an analysis of the susceptibility of a particular bundled overhead line to galloping. It presents a case study of an aerial bundled cable, consisting of four conductors insulated by polyethylene, and used for low-voltage power lines. The susceptibility to loss of stability is analyzed for cable without and with simulated icing observed on similar real conductors. In the first case, the proneness to galloping was excluded based on the results of CFD simulation and the Den Hartog criterion. In latter case, the possible occurrence of galloping was confirmed. The critical wind velocity for the ice-covered cable was calculated utilizing quasi-steady theory. Finally, the amplitudes of limit cycle oscillation for supercritical wind speeds were estimated based on simplified numerical analysis. Keywords: aerial bundled cable; wind effects; galloping; limit cycle oscillation Available in digital repository of the ASCR
Galloping of insulated bundled overhead line simplified analysis

Our paper provides an analysis of the susceptibility of a particular bundled overhead line to galloping. It presents a case study of an aerial bundled cable, consisting of four conductors insulated by ...

Hračov, Stanislav; Macháček, Michael
Ústav teoretické a aplikované mechaniky, 2024

LES simulations of airflow around rectangle with side ratio 2:1 and their comparison with experiments
Ledvinková, Blanka; Hračov, Stanislav; Macháček, Michael
2024 - English
Our contribution is focused on the comparison of the experimental investigations and of the numerical 3D LES simulations of the airflow around sharply edged rectangle with side ratio 2:1. The rectangle object was exposed to the airflow having a given velocity at different angles of the wind attack in the wind tunnel with the aim to obtain the curves of the aerodynamic coefficients and Strouhal number depending on the impact angle. The comparative numerical 3D simulations of the wind tunnel testing were performed using COMSOL Multiphysics and OpenFoam both incorporating the Large Eddy Simulation (LES) method. Keywords: rectangle 2:1; wind tunnel; LES simulation; aerodynamic characteristics Available in digital repository of the ASCR
LES simulations of airflow around rectangle with side ratio 2:1 and their comparison with experiments

Our contribution is focused on the comparison of the experimental investigations and of the numerical 3D LES simulations of the airflow around sharply edged rectangle with side ratio 2:1. The ...

Ledvinková, Blanka; Hračov, Stanislav; Macháček, Michael
Ústav teoretické a aplikované mechaniky, 2024

Využití termografie v průzkumech památek
Valach, Jaroslav; Eisler, Marek
2024 - Czech
Termografie rozšiřuje portfolia metod, jimiž lze studovat vlastnosti objektů okolního světa. Ještě před deseti lety byla tato technologie kvůli potenciálním vojenským aplikacím úzkostlivě kontrolována, což omezovalo konkurenci v nabídce výrobků a výrobců a vedlo k vysokým cenám zařízení založených na těchto principech. Teprve díky uvolnění této kontroly došlo k rozmachu výroby a zpřístupnění zjednodušených výrobků masovému využití, takže si dnes může zákazník například pořídit chytrý telefon s doplňkovým termografickým modulem jen s malým navýšením ceny. Spolu s dostupností zařízení pozorujeme nárůst uplatnění termografie v mnoha oblastech, včetně průzkumů staveb a památek. Thermography expands the portfolio of methods that can be used to study the properties of objects in the surrounding world. As recently as a decade ago, the technology was frowned upon for potential military applications controlled, which limited competition in the offer of products and manufacturers and led to high prices of devices based on these principles. It was only thanks to the release of this control that it happened to expand production and make simplified products available to mass use, so get it today for example, a customer can purchase a smartphone with an additional thermographic module for only with a small price increase. Together with the availability of equipment, we observe an increase in the application of thermography in many areas, including surveys of buildings and monuments. Keywords: thermography; survey of historical structures Available at various institutes of the ASCR
Využití termografie v průzkumech památek

Termografie rozšiřuje portfolia metod, jimiž lze studovat vlastnosti objektů okolního světa. Ještě před deseti lety byla tato technologie kvůli potenciálním vojenským aplikacím úzkostlivě ...

Valach, Jaroslav; Eisler, Marek
Ústav teoretické a aplikované mechaniky, 2024

Galloping of insulated bundled overhead line - nonlinear numerical analysis in time domain
Macháček, Michael; Hračov, Stanislav
2024 - English
Our contribution focuses on a 3D numerical nonlinear analysis of galloping in a specific bundled overhead line with ice accretion. We studied the susceptibility to this self-excited oscillation, critical onset wind speeds, and global dynamic response of a very low-tensioned line with simulated icing observed on similar real conductors. Due to the highly nonlinear mechanical behavior of such a flexible cable, we employed the Newmark integration method combined with the iterative Newton-Raphson method. We analyzed two numerical models of the overhead line loaded by the wind: one assuming nonlinearity only in the wind load, while retaining the linearity of the mechanical system itself, and the other representing a fully nonlinear system including geometrical nonlinearity. Our analysis revealed that the determined critical wind speeds for the onset of galloping are in relatively close ranges for both models. However, numerical simulations with the fully nonlinear system indicated significantly lower amplitudes of limit cycle oscillations, especially at higher wind speeds, compared to the linear model of the line. This underscores the necessity of using fully nonlinear models during the design stage of such low-tensioned aerial conductors. Keywords: aerial bundled conductors; wind effects; galloping; limit cycle oscillation Available in digital repository of the ASCR
Galloping of insulated bundled overhead line - nonlinear numerical analysis in time domain

Our contribution focuses on a 3D numerical nonlinear analysis of galloping in a specific bundled overhead line with ice accretion. We studied the susceptibility to this self-excited oscillation, ...

Macháček, Michael; Hračov, Stanislav
Ústav teoretické a aplikované mechaniky, 2024

Stochastic version of the arc-length method
Náprstek, Jiří; Fischer, Cyril
2024 - English
The solution of a nonlinear algebraic system using the incremental method, based on pre-defined loading steps, fails in the vicinity of local extrema as well as around bifurcation points. The solution involved the derivation of the so-called ’Arc-Length’ method. Its essence lies in not incrementing the system parameter or any of the independent variables but rather the length of the response curve. The stochastic variant of this method allows for working with a system where system parameters include random imperfections. This contribution presents a variant that tracks the first two stochastic moments. Even in this simple case, interesting phenomena can be observed, such as the disappearance of the energy barrier against equilibrium jump due to random imperfections in the system. Keywords: random imperfection; stochastic arc-length method; continuation; numerical method Available in digital repository of the ASCR
Stochastic version of the arc-length method

The solution of a nonlinear algebraic system using the incremental method, based on pre-defined loading steps, fails in the vicinity of local extrema as well as around bifurcation points. The solution ...

Náprstek, Jiří; Fischer, Cyril
Ústav teoretické a aplikované mechaniky, 2024

Acoustic emission methods in steel bridge degradation identification and monitoring
Šorm, Filip
2024 - English
Acoustic emission methods proved to be an effective diagnostic tool in many industrial sectors. The potential of this method in the field of steel bridge diagnostics is explored in this article. The goal is to find the most effective use of this method. Keywords: steel bridges; diagnostics; acoustic emission Available in digital repository of the ASCR
Acoustic emission methods in steel bridge degradation identification and monitoring

Acoustic emission methods proved to be an effective diagnostic tool in many industrial sectors. The potential of this method in the field of steel bridge diagnostics is explored in this article. The ...

Šorm, Filip
Ústav teoretické a aplikované mechaniky, 2024

Výzkum zříceniny hradu Štamberk v kontextu regionu
Novotný, Jakub; Ramešová, Michaela
2023 - Czech
Příspěvek přibližuje dosavadní výsledky výzkumu hradu Štamberk realizovaného dle nově definovaných zásad pro výzkum, správu a prezentaci historických zřícenin, jehož cílem je podpořit nová řešení jak zvýšit využitelnost hradu pro cestovní ruch a integrovat památku do regionálních struktur lokalit s potenciálem cestovního ruchu. Hrad byl významným panstvím v rámci území dnešní Vysočiny. Předmětem řešení projektu, na kterém od roku 2020 spolupracuje ÚTAM AV ČR s Mikroregionem Telčsko, je výzkum historie hradu se zaměřením na technologická hlediska jeho výstavby, stavebních změn i zániku. Součástí je vytvoření 3D modelu zříceniny v krajinném kontextu. Projekt se soustředí na dějiny výroby vápna a související inventarizaci geologických lokalit. Tento výzkum přináší nové informace důležité nejen pro poznání historie hradu či pro studium analogických situací, ale také pro zvýšení atraktivity památky pro cestovní ruch. Příspěvek nejprve představí aktuální standardy výzkumu a managementu zřícenin, následně se bude zabývat nástinem potenciálu výzkumu Štamberka pro oblast cestovního ruchu s důrazem na historii hradu, mapování krajinného rámce a identifikace vazeb na regionální prostředí. Na závěr zrekapituluje dosavadní výsledky využitelné k prezentaci historického, kulturního i přírodního bohatství regionu se specifickou vazbou na cestovní ruch. The paper provides an overview of the research results of the Štamberk castle carried out according to newly defined principles for the research, management and presentation of historical ruins, the aim of which is to support new solutions to increase the usability of the castle for tourism and to integrate the monument into the regional structures of localities with tourism potential. The castle was an important place within the territory of today's Highlands. The subject of the project, on which ITAM CAS has been collaborating with the Telčsko Microregion since 2020, is research into the history of the castle with a focus on the technological aspects of its construction, structural changes and demise. It includes the creation of a 3D model of the ruins in a landscape context. The project focuses on the history of lime production and the related inventory of geological sites. This research brings new information important not only for learning about the history of the castle or for studying analogous situations, but also for increasing the attractiveness of the monument for tourism. The paper first presents the current standards of research and management of ruins, then it deals with an outline of the research potential of Štamberk for the field of tourism with an emphasis on the history of the castle, mapping the landscape framework and identifying links to the regional environment. At the end, it summarizes the results so far that can be used to present the historical, cultural and natural wealth of the region with a specific link to tourism. Keywords: Štamberk; ruin; technological research; presentation of monuments; tourism Available at various institutes of the ASCR
Výzkum zříceniny hradu Štamberk v kontextu regionu

Příspěvek přibližuje dosavadní výsledky výzkumu hradu Štamberk realizovaného dle nově definovaných zásad pro výzkum, správu a prezentaci historických zřícenin, jehož cílem je podpořit nová řešení jak ...

Novotný, Jakub; Ramešová, Michaela
Ústav teoretické a aplikované mechaniky, 2023

Adaptation of methods for cyclo-stationary processes for noisy structural health data
Fischer, Cyril; Bayer, Jan; Náprstek, Jiří; Urushadze, Shota
2023 - English
In structural health analysis, various techniques, including indirect measurement via monitoring vehicles, often yield data with significant randomness and insufficient frequency separation. Conversely, the desired attributes under scrutiny are periodic in nature. Thus, methodologies designed to identify cyclo-stationary properties within noisy data can be adapted for such scenarios, assuming an adequate length of the recorded data. Keywords: data analysis; cyclo-stationary processes; structural health monitoring Available at various institutes of the ASCR
Adaptation of methods for cyclo-stationary processes for noisy structural health data

In structural health analysis, various techniques, including indirect measurement via monitoring vehicles, often yield data with significant randomness and insufficient frequency separation. ...

Fischer, Cyril; Bayer, Jan; Náprstek, Jiří; Urushadze, Shota
Ústav teoretické a aplikované mechaniky, 2023

About project

NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web

Send your suggestions and comments to nusl@techlib.cz

Provider

http://www.techlib.cz

Facebook

Other bases