No (1755)
Number of found documents:
1755
Published from
to
Dynamics of Machines and Mechanical Systems with Interactions, DYMAMESI 2021
Zolotarev, Igor; Pešek, Luděk; Kozień, M. S.
2021 - English
The aim of the DYMAMESI is to facilitate the exchange of up to date information and knowledge among specialists in structural and multibody dynamics, in coupled interacting systems as aero-elasticity, hydro-elasticity, biomechanics, systems with feedbacks and mechatronics. The colloquium DYMAMESI 2021 is cofunded by the Strategy AV21 initiative of the Czech Academy of Sciences of the Czech Republic, and in 2021 will be hosted by Cracow University of Technology, Institute of Applied Mechanics, Section of Dynamics of Systems.
Keywords:
dynamics; vibrations of mechanical systems; vibrodiagnostics; energy transformations
Available at various institutes of the ASCR
Dynamics of Machines and Mechanical Systems with Interactions, DYMAMESI 2021
The aim of the DYMAMESI is to facilitate the exchange of up to date information and knowledge among specialists in structural and multibody dynamics, in coupled interacting systems as aero-elasticity, ...
The new HPC results of 3D FE modelling of dry-friction damping at tie-boss couplings of bladed wheel - 6nd resonant mode
Pešek, Luděk; Šnábl, Pavel; Bula, Vítězslav
2021 - English
The paper is a direct continuation of our study published in the last colloquium DYMAMESI. This paper deals with the new results of dry-friction damping calculation of the bladed wheel with tie-boss couplings vibrating at a higher resonant mode, i.e. mode with 6 nodal diameters (ND). The numerical solution of the wheel based on 3D finite element method with surface-to-surface dry friction contact model is applied. Due to dry friction contacts and non-linear solution, it leads to HPC computations and long computation times. Therefore, the earlier proposed computational strategy for damping evaluation where the resonant attenuation is computed directly from the defined resonant initial conditions given by the 6ND mode is used. Comparison of experimental and numerical results of dynamical behaviour of the bladed wheel yields a reasonable agreement for the studied vibration mode.
Keywords:
bladed wheel; dry-friction contacts; damping; tie-boss couplings
Available at various institutes of the ASCR
The new HPC results of 3D FE modelling of dry-friction damping at tie-boss couplings of bladed wheel - 6nd resonant mode
The paper is a direct continuation of our study published in the last colloquium DYMAMESI. This paper deals with the new results of dry-friction damping calculation of the bladed wheel with tie-boss ...
Verification of our deformation member for measuring axial force under torsional dynamic load
Šulc, Petr; Pešek, Luděk; Štěpánek, Ivo; Šnábl, Pavel; Bula, Vítězslav
2021 - English
This paper deals with experimental testing of hard rubbers under torsional harmonic loading on an axial torsional servohydraulic testing machine Instron 8852. In evaluating these experiments, we focused on obtaining axial forces and elongation, which is a confirmation of the so-called Poynting effect under torsional loading. An important result from these experiments is a comparison of axial forces from this device with the results from our designed and assembled torsion device with a deformation member for measuring axial forces, which brings us some verification of this device.
Keywords:
axial force; torsion dynamic load; hard rubber; Poynting effect
Available at various institutes of the ASCR
Verification of our deformation member for measuring axial force under torsional dynamic load
This paper deals with experimental testing of hard rubbers under torsional harmonic loading on an axial torsional servohydraulic testing machine Instron 8852. In evaluating these experiments, we ...
Numerical simulation of dynamic loading of a test blade in forced torsional vibration
Šidlof, P.; Vomáčko, V.; Lepičovský, Jan; Šimurda, David; Štěpán, M.; Luxa, Martin
2021 - English
Within a new project focused on blade flutter research, building on previous experience with the NASA Transonic Flutter Cascade facility, static blade cascade and airfoil flutter experiments realized in cooperation between the Institute of Thermomechanics and Technical University of Liberec, a new test facility is under development for the investigation of high subsonic and transonic flow in a blade cascade under forced torsional oscillation. Apart from aerodynamic loading of the blades, the oscillating blade will be exposed to significant structural stresses due to the highfrequency torsional vibration. In order to avoid structural integrity issues from high-cycle fatigue, a numerical simulation of the stress and displacement of the blade was realized. Regions where equivalent stress reaches maximum values were identified, and elastic deformations were computed. The limits in oscillation amplitude and frequency for the safe operation of the experimental setup were discussed.
Keywords:
blade flutter; structural analysis; torsional vibration
Available at various institutes of the ASCR
Numerical simulation of dynamic loading of a test blade in forced torsional vibration
Within a new project focused on blade flutter research, building on previous experience with the NASA Transonic Flutter Cascade facility, static blade cascade and airfoil flutter experiments realized ...
A simple algorithm for probes positioning in BTT systems
Tchawou Tchuisseu, Eder Batista; Procházka, Pavel; Maturkanič, Dušan
2020 - English
The Blade Tip Timing (BTT), a non-contact method for measuring the blade tip displacement through the time of arrival, is studied in this article. This work proposes a simple algorithm based on the minimization of the coherence and the condition number of the sensingmatrix for defining the best probe positioning in the case of synchronous and asynchronous vibrations.
Keywords:
BTT systems; probe positioning; condition number; coherence
Available at various institutes of the ASCR
A simple algorithm for probes positioning in BTT systems
The Blade Tip Timing (BTT), a non-contact method for measuring the blade tip displacement through the time of arrival, is studied in this article. This work proposes a simple algorithm based on the ...
Comparison of power control method for B4 converter connected to unbalanced grid
Šimek, Petr; Valouch, Viktor
2020 - English
The aim of the paper is to present a power control of a three-phase inverter with only four inverter legs (connections B4) connected to an unbalanced grid. The results obtained by the predictive power control with a finite set of control values, the results obtained using a modified direct power control strategy, and the results obtained using a generalized predictive control are compared and discussed.\n
Keywords:
power control; B4 converter; unbalanced grid
Available at various institutes of the ASCR
Comparison of power control method for B4 converter connected to unbalanced grid
The aim of the paper is to present a power control of a three-phase inverter with only four inverter legs (connections B4) connected to an unbalanced grid. The results obtained by the predictive power ...
Contribution to HPC FEM calculations of bladed disk dynamics with dry-friction contacts
Pešek, Luděk; Šnábl, Pavel; Bula, Vítězslav
2020 - English
The experimental set-up for studying dynamical behaviour of the bladed wheel with pre-stressed dry-friction contacts in tie-bosses was built. The numerical solution of the turbine bladed wheel with tie-bosses based on 3D finite element method with surface to surface dry-friction contact model is proposed. Comparison of experimental and preliminary numerical results of dynamical behaviour and damping estimation of our bladed wheel design yielded a reasonable agreement. Due to dry-friction contacts and non-linear solution of 3D FE model it, however, leads to HPC computations and long computation times. The contribution deals with description of computational strategy for damping evaluation and achieved results, too.
Keywords:
bladed wheel; dry-friction contacts; damping; tie-boss couplings
Available at various institutes of the ASCR
Contribution to HPC FEM calculations of bladed disk dynamics with dry-friction contacts
The experimental set-up for studying dynamical behaviour of the bladed wheel with pre-stressed dry-friction contacts in tie-bosses was built. The numerical solution of the turbine bladed wheel with ...
Design of experiment for temperature dependence of rubber samples under torsional harmonic load
Šulc, Petr; Pešek, Luděk; Bula, Vítězslav; Košina, Jan; Cibulka, Jan
2020 - English
This work deals with the preparation and methodology of temperature measurement inside the rubber sample. There is a design of a rubber sample with placed temperature sensors and a description with a scheme of temperature measurement under torsional dynamic stress. The reason for these measurements is to determine the temperature dependence and sensitivity of the parameters of the thermal outputs.
Keywords:
heat flow; temperature; Fourier equation
Available at various institutes of the ASCR
Design of experiment for temperature dependence of rubber samples under torsional harmonic load
This work deals with the preparation and methodology of temperature measurement inside the rubber sample. There is a design of a rubber sample with placed temperature sensors and a description with a ...
Experimental modelling of vibroacoustics of the human vocal tract with compliant walls
Radolf, Vojtěch; Horáček, Jaromír; Košina, Jan
2020 - English
Experimental model of human vocal tract cavities with hard walls has been modified to take into account the compliance of the soft tissue of the human vocal tract. The paper presents the studied acoustic-structural interaction of the vocal tract cavities with a dynamical system originated in vibration of the soft tissue. The experimental results are in qualitative agreement with the results of mathematical modelling. Compliant walls of acoustic cavities generate additional low frequency acoustical-mechanical resonances of the system and increase acoustic resonance frequencies.
Keywords:
biomechanics of voice; vocal tract acoustics; acoustic-structural interaction.
Available at various institutes of the ASCR
Experimental modelling of vibroacoustics of the human vocal tract with compliant walls
Experimental model of human vocal tract cavities with hard walls has been modified to take into account the compliance of the soft tissue of the human vocal tract. The paper presents the studied ...
Dependence of signal strangth on the radial distance and different types of magnets
Procházka, Pavel; Voronova, Evgeniya; Maturkanič, Dušan
2020 - English
The paper describes dependence of signal strength on the radial distance between the sensor and the measured object and dependence of signal strength on the different types of magnets. The measurements were performed in the laboratory of the rotational laser vibrometry originated at the Institute of Thermomechanics AS CR, v.v.i.
Keywords:
vibration; diagnostics; sensor; laser; blade; turbine
Available at various institutes of the ASCR
Dependence of signal strangth on the radial distance and different types of magnets
The paper describes dependence of signal strength on the radial distance between the sensor and the measured object and dependence of signal strength on the different types of magnets. The ...
NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web
Send your suggestions and comments to nusl@techlib.cz
Provider
Other bases