Kráľova Lehota. Paleomagnetic research. Report
Elbra, Tiiu; Schnabl, Petr; Aidona, E.; Kdýr, Šimon; Uçar, Hakan; Pruner, Petr; Benediková, L.
2023 - anglický Klíčová slova: Archeological artefact; paleomagnetic dating; rock magnetism Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Kráľova Lehota. Paleomagnetic research. Report

Elbra, Tiiu; Schnabl, Petr; Aidona, E.; Kdýr, Šimon; Uçar, Hakan; Pruner, Petr; Benediková, L.
Geologický ústav, 2023

Reduced modelling of aeroelastic instability in a turbine blade cascade
Pešek, Luděk; Šnábl, Pavel; Prasad, Chandra Shekhar
2023 - anglický The contribution deals with the first results on flutter instability of the linear cascade triggered by impulse excitation. Together with experimental results, numerical results obtained by reduced modelling of the cascade using van der Pol model of self-excitation are presented and discussed. Klíčová slova: flutter; blade cascade; self-excitation; Van der Pol Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Reduced modelling of aeroelastic instability in a turbine blade cascade

The contribution deals with the first results on flutter instability of the linear cascade triggered by impulse excitation. Together with experimental results, numerical results obtained by reduced ...

Pešek, Luděk; Šnábl, Pavel; Prasad, Chandra Shekhar
Ústav termomechaniky, 2023

Implementation of a plasticity model with advanced kinematic hardening rule for additively manufactured materials
Marek, René; Parma, Slavomír; Gabriel, Dušan; Džugan, J.
2023 - anglický This technical report summarizes particularly the modeling part of the project DP 04_01_NPO “Emission-free technologies for local energy sources replacement” including development of models to describe multi-material 3D printed structures. The work is done in cooperation between COMTES FHT, a.s., the Institute of Thermomechanics of the Czech Academy of Sciences, v.v.i. and PROINNO, a.s. The goal of the project is the development of material models describing the behavior of multi-material components deposited by the direct deposition method (DED) under multiaxial cyclic loading.\nIn the report, a plasticity model suitable for materials prepared by the additive manufacturing method is compiled and used. The model uses Hill's plasticity condition, an advanced multi-component kinematic hardening rule, and an isotropic hardening rule. The associated flow rule is chosen and the implementation assumes the theory of small deformations. All constitutive relationships are presented and discussed for the selected model, and the model is thus fully and unambiguously formulated. The model is analytically integrated for a special case of loading and a special choice of parameters of the plasticity condition, namely transverse isotropy. A discretization scheme for numerical integration and procedures for FE implementation of the model are presented. For the FE implementation, a formulation in the displacement field is assumed, specifically the FE solver Abaqus and the implementation of the model using the UMAT interface are targeted. Several examples of the model's response to monotonic, uniaxial and biaxial cyclic loading trajectories are presented. \n Tato zpráva shrnuje postup prací na dílčím projektu DP 04_01_NPO “Emission-free technologies for local energy sources replacement” zahrnující vývoj modelů pro popis chování multi-materiálových 3D tištěných struktur řešený v konsorciu COMTES FHT, a.s., Ústav termomechaniky AV ČR, v.v.i. a PROINNO, a.s. Cílem projektu je vývoj materiálových modelů popisujících chování multi-materiálových komponent deponovaných metodou přímé depozice (DED) pří víceosém cyklickém zatěžování. \nVe zprávě je sestaven a použit model plasticity vhodný pro materiály připravené metodou aditivní výroby. Model využívá Hillovu podmínku plasticity, pokročilý vícesložkový model kinematického zpevnění a model isotropního zpevnění. Je zvolen asociovaný zákon tečení a implementace předpokládá teorii malých deformací. Pro zvolený model jsou uvedeny a diskutovány všechny konstitutivní vztahy a model je tak plně a jednoznačně formulován. Model je analyticky integrován pro speciální případ zatěžování a speciální volbu parametrů podmínky plasticity, konkrétně příčnou isotropii. Je prezentováno diskretizační schema pro numerickou integraci a procedury pro MKP implementaci modelu. U MKP implementace se předpokládá formulace v poli posunutí, konkrétně je pak cíleno na MKP řešič Abaqus a implementaci modelu pomocí rozhraní UMAT. Je prezentováno několik příkladů odezvy modelu na monotónní, jednoosé a víceosé cycklické zatěžovací trajektorie.\n Klíčová slova: plasticity; anisotropy; additive manufacturing Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Implementation of a plasticity model with advanced kinematic hardening rule for additively manufactured materials

This technical report summarizes particularly the modeling part of the project DP 04_01_NPO “Emission-free technologies for local energy sources replacement” including development of models to ...

Marek, René; Parma, Slavomír; Gabriel, Dušan; Džugan, J.
Ústav termomechaniky, 2023

Annular Impinging Jets and an Active Control of Hysteretic Effects
Devani, Yogendrasasidhar; Antošová, Zuzana; Trávníček, Zdeněk
2023 - anglický An annular impinging air jet with and without flow control was studied experimentally using measurements of the wall pressure and flow velocity by the Pitot probe. To investigate flow control swirling effects, eight synthetic jets were generated from the nozzle center body. The experiments cover Reynolds numbers 4000–10,000 (evaluated from the outer exit diameter of the annular nozzle). For Re<9000, the bistability and hysteresis were identified and two different flow field patterns (A, B) were found under the same boundary conditions. For higher Re>9000, the hysteresis were not found. Klíčová slova: annular jet; impinging jet; hysteresis Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Annular Impinging Jets and an Active Control of Hysteretic Effects

An annular impinging air jet with and without flow control was studied experimentally using measurements of the wall pressure and flow velocity by the Pitot probe. To investigate flow control swirling ...

Devani, Yogendrasasidhar; Antošová, Zuzana; Trávníček, Zdeněk
Ústav termomechaniky, 2023

Stereolithography for manufacturing of advanced porous solids
Drechslerová, V.; Neuhäuserová, M.; Falta, J.; Šleichrt, J.; Kytýř, Daniel
2023 - anglický The aim of this paper is focused on benefits of stereolithography (SLA) technology for the fabrication of the lightweight lattice structures with potential for load-bearing function and high absorption of impact energy. SLA is an additive manufacturing technology employing the principle of liquid resins curing moderated by radiation of a wavelength from ultra-violet band where resulting material parameters are tunable by setting of the curing process. The batches of samples manufactured using three different resins were subjected to quasi-static uni-axial tensile and compression tests. Acquired data were processed to derive deformation behaviour expressed as stress-strain diagrams and fundamental material properties. Based on the knowledge obtained from the mechanical tests, the setup of the fabrication parameters, the most suitable resin for manufacturing of the lattice structures and the overall suitability of SLA technology for the fabrication of advanced porous materials, were determined. Klíčová slova: stereolithography; advanced porous materials; quasi-static testing; resin; mechanical characteristics Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Stereolithography for manufacturing of advanced porous solids

The aim of this paper is focused on benefits of stereolithography (SLA) technology for the fabrication of the lightweight lattice structures with potential for load-bearing function and high ...

Drechslerová, V.; Neuhäuserová, M.; Falta, J.; Šleichrt, J.; Kytýř, Daniel
Ústav teoretické a aplikované mechaniky, 2023

Caves in Bohemia et Moravia Subterranea by Mauritius Vogt (1669–1730)
Rychnová, L.; Vokurka, Michal
2023 - anglický The Manuscript Bohemia et Moravia Subterranea (1729) by Mauritius Vogt reflects the subterranean landscapes and underground spaces based on Athanasius Kircher’s theories. The paper analyses the application of Kirchers’s terminology to the natural phenomena from Bohemia and Moravia. Further, we focused on how Vogt worked with his sources – how far he relied on literature, correspondence, or personal experience. Klíčová slova: Mauritius Vogt; caves; subterranean; underground; early modern period Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Caves in Bohemia et Moravia Subterranea by Mauritius Vogt (1669–1730)

The Manuscript Bohemia et Moravia Subterranea (1729) by Mauritius Vogt reflects the subterranean landscapes and underground spaces based on Athanasius Kircher’s theories. The paper analyses the ...

Rychnová, L.; Vokurka, Michal
Historický ústav, 2023

A new blade cascade for flutter studies
Šnábl, Pavel; Pešek, Luděk; Procházka, Pavel P.; Skála, V.
2023 - anglický In this paper, a new blade cascade, developed in the Institute of Thermomechanics, is presented. The geometry of the cascade was modified so now the stall flutter can occur. It has some major construction improvements over the original cascade which now allow more precise and reliable measurements. The stability of the new blade cascade with five NACA 0010 profiles with rotational degree of freedom is assessed by Travelling Wave Mode approach and Aerodynamic Influence Coefficient approach. Klíčová slova: blade cascade; stability; travelling wave mode; aerodynamic influence coefficient Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. A new blade cascade for flutter studies

In this paper, a new blade cascade, developed in the Institute of Thermomechanics, is presented. The geometry of the cascade was modified so now the stall flutter can occur. It has some major ...

Šnábl, Pavel; Pešek, Luděk; Procházka, Pavel P.; Skála, V.
Ústav termomechaniky, 2023

Novel embedding resins for 3D-SEM II
Šlouf, Miroslav; Pavlova, Ewa; Strachota, Beata; Strachota, Adam; Nebesářová, Jana; Týč, Jiří; Krzyžánek, Vladislav; Skoupý, Radim
2023 - anglický Research report for Thermo Fisher Scientific s. r. o., based on common project awarded by TA CR (program: National center of competence, TN01000008). Klíčová slova: novel embedding resins; 3D-SEM microscopy; higher e-beam resistance Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Novel embedding resins for 3D-SEM II

Research report for Thermo Fisher Scientific s. r. o., based on common project awarded by TA CR (program: National center of competence, TN01000008).

Šlouf, Miroslav; Pavlova, Ewa; Strachota, Beata; Strachota, Adam; Nebesářová, Jana; Týč, Jiří; Krzyžánek, Vladislav; Skoupý, Radim
Ústav makromolekulární chemie, 2023

An Enzymatic Biosensor with Amperometric Detection in a Flow Injection Analysis for the Determination of L-lactic Acid: Development and Application
Tvorynska, Sofiia; Barek, J.; Josypčuk, Bohdan
2023 - anglický An amperometric biosensor consisting of an enzymatic mini-reactor (lactate oxidase covalently\nattached to −NH2 functionalized mesoporous silica powder SBA−15 using glutaraldehyde) and\na silver amalgam-based screen-printed electrode acting as a transducer was developed for the\ndetermination of L-lactic acid (LA) in FIA. The detection potential of −0.9 V vs. Ag pseudoreference\nelectrode was applied for cathodic detection of enzymatically consumed oxygen.\nUnder the optimized conditions, the constructed biosensor enabled selective determination of\nLA with a micromolar limit of detection. Importantly, the proposed biosensor represented\nexcellent operational stability after ≥350 measurements. Finally, it was successfully applied to\nreal sample analysis. Klíčová slova: L-lactic acid; Lactate oxidase; Amperometric biosensor; silver amalgam Plné texty jsou dostupné na vyžádání prostřednictvím repozitáře Akademie věd. An Enzymatic Biosensor with Amperometric Detection in a Flow Injection Analysis for the Determination of L-lactic Acid: Development and Application

An amperometric biosensor consisting of an enzymatic mini-reactor (lactate oxidase covalently\nattached to −NH2 functionalized mesoporous silica powder SBA−15 using glutaraldehyde) and\na silver ...

Tvorynska, Sofiia; Barek, J.; Josypčuk, Bohdan
Ústav fyzikální chemie J. Heyrovského, 2023

Identification of quasiperiodic processes in the vicinity of the resonance
Fischer, Cyril; Náprstek, Jiří
2023 - anglický In nonlinear dynamical systems, strong quasiperiodic beating effects appear due to combination of self-excited and forced vibration. The presence of symmetric or asymmetric beatings indicates an exchange of energy between individual degrees of freedom of the model or by multiple close dominant frequencies. This effect is illustrated by the case of the van der Pol equation in the vicinity of resonance. The approximate analysis of these nonlinear effects uses the harmonic balance method and the multiple scale method. Klíčová slova: dynamical systems; quasiperiodic response; van der Pol equation Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR. Identification of quasiperiodic processes in the vicinity of the resonance

In nonlinear dynamical systems, strong quasiperiodic beating effects appear due to combination of self-excited and forced vibration. The presence of symmetric or asymmetric beatings indicates an ...

Fischer, Cyril; Náprstek, Jiří
Ústav teoretické a aplikované mechaniky, 2023