Ne (1755)
Počet nalezených dokumentů:
1755
Publikováno od
do
Dynamics of Machines and Mechanical Systems with Interactions, DYMAMESI 2021
Zolotarev, Igor; Pešek, Luděk; Kozień, M. S.
2021 - anglický
The aim of the DYMAMESI is to facilitate the exchange of up to date information and knowledge among specialists in structural and multibody dynamics, in coupled interacting systems as aero-elasticity, hydro-elasticity, biomechanics, systems with feedbacks and mechatronics. The colloquium DYMAMESI 2021 is cofunded by the Strategy AV21 initiative of the Czech Academy of Sciences of the Czech Republic, and in 2021 will be hosted by Cracow University of Technology, Institute of Applied Mechanics, Section of Dynamics of Systems.
Klíčová slova:
dynamics; vibrations of mechanical systems; vibrodiagnostics; energy transformations
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Dynamics of Machines and Mechanical Systems with Interactions, DYMAMESI 2021
The aim of the DYMAMESI is to facilitate the exchange of up to date information and knowledge among specialists in structural and multibody dynamics, in coupled interacting systems as aero-elasticity, ...
The new HPC results of 3D FE modelling of dry-friction damping at tie-boss couplings of bladed wheel - 6nd resonant mode
Pešek, Luděk; Šnábl, Pavel; Bula, Vítězslav
2021 - anglický
The paper is a direct continuation of our study published in the last colloquium DYMAMESI. This paper deals with the new results of dry-friction damping calculation of the bladed wheel with tie-boss couplings vibrating at a higher resonant mode, i.e. mode with 6 nodal diameters (ND). The numerical solution of the wheel based on 3D finite element method with surface-to-surface dry friction contact model is applied. Due to dry friction contacts and non-linear solution, it leads to HPC computations and long computation times. Therefore, the earlier proposed computational strategy for damping evaluation where the resonant attenuation is computed directly from the defined resonant initial conditions given by the 6ND mode is used. Comparison of experimental and numerical results of dynamical behaviour of the bladed wheel yields a reasonable agreement for the studied vibration mode.
Klíčová slova:
bladed wheel; dry-friction contacts; damping; tie-boss couplings
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
The new HPC results of 3D FE modelling of dry-friction damping at tie-boss couplings of bladed wheel - 6nd resonant mode
The paper is a direct continuation of our study published in the last colloquium DYMAMESI. This paper deals with the new results of dry-friction damping calculation of the bladed wheel with tie-boss ...
Verification of our deformation member for measuring axial force under torsional dynamic load
Šulc, Petr; Pešek, Luděk; Štěpánek, Ivo; Šnábl, Pavel; Bula, Vítězslav
2021 - anglický
This paper deals with experimental testing of hard rubbers under torsional harmonic loading on an axial torsional servohydraulic testing machine Instron 8852. In evaluating these experiments, we focused on obtaining axial forces and elongation, which is a confirmation of the so-called Poynting effect under torsional loading. An important result from these experiments is a comparison of axial forces from this device with the results from our designed and assembled torsion device with a deformation member for measuring axial forces, which brings us some verification of this device.
Klíčová slova:
axial force; torsion dynamic load; hard rubber; Poynting effect
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Verification of our deformation member for measuring axial force under torsional dynamic load
This paper deals with experimental testing of hard rubbers under torsional harmonic loading on an axial torsional servohydraulic testing machine Instron 8852. In evaluating these experiments, we ...
Numerical simulation of dynamic loading of a test blade in forced torsional vibration
Šidlof, P.; Vomáčko, V.; Lepičovský, Jan; Šimurda, David; Štěpán, M.; Luxa, Martin
2021 - anglický
Within a new project focused on blade flutter research, building on previous experience with the NASA Transonic Flutter Cascade facility, static blade cascade and airfoil flutter experiments realized in cooperation between the Institute of Thermomechanics and Technical University of Liberec, a new test facility is under development for the investigation of high subsonic and transonic flow in a blade cascade under forced torsional oscillation. Apart from aerodynamic loading of the blades, the oscillating blade will be exposed to significant structural stresses due to the highfrequency torsional vibration. In order to avoid structural integrity issues from high-cycle fatigue, a numerical simulation of the stress and displacement of the blade was realized. Regions where equivalent stress reaches maximum values were identified, and elastic deformations were computed. The limits in oscillation amplitude and frequency for the safe operation of the experimental setup were discussed.
Klíčová slova:
blade flutter; structural analysis; torsional vibration
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Numerical simulation of dynamic loading of a test blade in forced torsional vibration
Within a new project focused on blade flutter research, building on previous experience with the NASA Transonic Flutter Cascade facility, static blade cascade and airfoil flutter experiments realized ...
A simple algorithm for probes positioning in BTT systems
Tchawou Tchuisseu, Eder Batista; Procházka, Pavel; Maturkanič, Dušan
2020 - anglický
The Blade Tip Timing (BTT), a non-contact method for measuring the blade tip displacement through the time of arrival, is studied in this article. This work proposes a simple algorithm based on the minimization of the coherence and the condition number of the sensingmatrix for defining the best probe positioning in the case of synchronous and asynchronous vibrations.
Klíčová slova:
BTT systems; probe positioning; condition number; coherence
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
A simple algorithm for probes positioning in BTT systems
The Blade Tip Timing (BTT), a non-contact method for measuring the blade tip displacement through the time of arrival, is studied in this article. This work proposes a simple algorithm based on the ...
Contribution to HPC FEM calculations of bladed disk dynamics with dry-friction contacts
Pešek, Luděk; Šnábl, Pavel; Bula, Vítězslav
2020 - anglický
The experimental set-up for studying dynamical behaviour of the bladed wheel with pre-stressed dry-friction contacts in tie-bosses was built. The numerical solution of the turbine bladed wheel with tie-bosses based on 3D finite element method with surface to surface dry-friction contact model is proposed. Comparison of experimental and preliminary numerical results of dynamical behaviour and damping estimation of our bladed wheel design yielded a reasonable agreement. Due to dry-friction contacts and non-linear solution of 3D FE model it, however, leads to HPC computations and long computation times. The contribution deals with description of computational strategy for damping evaluation and achieved results, too.
Klíčová slova:
bladed wheel; dry-friction contacts; damping; tie-boss couplings
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Contribution to HPC FEM calculations of bladed disk dynamics with dry-friction contacts
The experimental set-up for studying dynamical behaviour of the bladed wheel with pre-stressed dry-friction contacts in tie-bosses was built. The numerical solution of the turbine bladed wheel with ...
Design of experiment for temperature dependence of rubber samples under torsional harmonic load
Šulc, Petr; Pešek, Luděk; Bula, Vítězslav; Košina, Jan; Cibulka, Jan
2020 - anglický
This work deals with the preparation and methodology of temperature measurement inside the rubber sample. There is a design of a rubber sample with placed temperature sensors and a description with a scheme of temperature measurement under torsional dynamic stress. The reason for these measurements is to determine the temperature dependence and sensitivity of the parameters of the thermal outputs.
Klíčová slova:
heat flow; temperature; Fourier equation
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Design of experiment for temperature dependence of rubber samples under torsional harmonic load
This work deals with the preparation and methodology of temperature measurement inside the rubber sample. There is a design of a rubber sample with placed temperature sensors and a description with a ...
Experimental modelling of vibroacoustics of the human vocal tract with compliant walls
Radolf, Vojtěch; Horáček, Jaromír; Košina, Jan
2020 - anglický
Experimental model of human vocal tract cavities with hard walls has been modified to take into account the compliance of the soft tissue of the human vocal tract. The paper presents the studied acoustic-structural interaction of the vocal tract cavities with a dynamical system originated in vibration of the soft tissue. The experimental results are in qualitative agreement with the results of mathematical modelling. Compliant walls of acoustic cavities generate additional low frequency acoustical-mechanical resonances of the system and increase acoustic resonance frequencies.
Klíčová slova:
biomechanics of voice; vocal tract acoustics; acoustic-structural interaction.
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Experimental modelling of vibroacoustics of the human vocal tract with compliant walls
Experimental model of human vocal tract cavities with hard walls has been modified to take into account the compliance of the soft tissue of the human vocal tract. The paper presents the studied ...
Comparison of power control method for B4 converter connected to unbalanced grid
Šimek, Petr; Valouch, Viktor
2020 - anglický
The aim of the paper is to present a power control of a three-phase inverter with only four inverter legs (connections B4) connected to an unbalanced grid. The results obtained by the predictive power control with a finite set of control values, the results obtained using a modified direct power control strategy, and the results obtained using a generalized predictive control are compared and discussed.\n
Klíčová slova:
power control; B4 converter; unbalanced grid
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Comparison of power control method for B4 converter connected to unbalanced grid
The aim of the paper is to present a power control of a three-phase inverter with only four inverter legs (connections B4) connected to an unbalanced grid. The results obtained by the predictive power ...
Dependence of signal strangth on the radial distance and different types of magnets
Procházka, Pavel; Voronova, Evgeniya; Maturkanič, Dušan
2020 - anglický
The paper describes dependence of signal strength on the radial distance between the sensor and the measured object and dependence of signal strength on the different types of magnets. The measurements were performed in the laboratory of the rotational laser vibrometry originated at the Institute of Thermomechanics AS CR, v.v.i.
Klíčová slova:
vibration; diagnostics; sensor; laser; blade; turbine
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Dependence of signal strangth on the radial distance and different types of magnets
The paper describes dependence of signal strength on the radial distance between the sensor and the measured object and dependence of signal strength on the different types of magnets. The ...
NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.
Vaše náměty a připomínky posílejte na email nusl@techlib.cz
Provozovatel
Zahraniční báze