Ne (6380)
Ano (948)
Počet nalezených dokumentů:
7328
Publikováno od
do
Souvislost mezi principem nejmenší akce a termodynamickou podmínkou stability
Maršík, František; Trávníček, Zdeněk; Antošová, Zuzana
2023 - anglický
The extended principle is formulated for a material point (M.P.) X, which has nonzero mass, temperature, and trajectory x(X,t). The Lagrangian of this variation principle is equal to the kinetic energy from which, the internal energy of the material point (which depends on the entropy) and the additional energy caused by the frictional force are subtracted. The relation between the inertial force and the entropy gradient is found and the gravitational force is completely replaced by the entropy gradient. Thanks to the mentioned properties of the total enthalpy, the Thermodynamic criterion of stability of the state of M.P., is formulated.
Klíčová slova:
principle of the least action; thermodynamic stability condition; annular swirl flow
Dokument je dostupný na externích webových stránkách.
Souvislost mezi principem nejmenší akce a termodynamickou podmínkou stability
The extended principle is formulated for a material point (M.P.) X, which has nonzero mass, temperature, and trajectory x(X,t). The Lagrangian of this variation principle is equal to the kinetic ...
Texture Spectral Similarity Criteria Comparison
Havlíček, Michal; Haindl, Michal
2023 - anglický
Criteria capable of texture spectral similarity evaluation are presented and compared. From the fifteen evaluated criteria, only four criteria guarantee zero or minimal spectral ranking errors. Such criteria can support texture modeling algorithms by comparing the modeled texture with corresponding synthetic simulations. Another possible application is the development of texture retrieval, classification, or texture acquisition system. These criteria thoroughly test monotonicity and mutual correlation on specifically designed extensive monotonously degrading experiments.
Klíčová slova:
Texture Comparison; Texture Modeling; Texture Retrieval; Texture Classification; Texture Acquisition
Dokument je dostupný na externích webových stránkách.
Texture Spectral Similarity Criteria Comparison
Criteria capable of texture spectral similarity evaluation are presented and compared. From the fifteen evaluated criteria, only four criteria guarantee zero or minimal spectral ranking errors. Such ...
Stereolithography for manufacturing of advanced porous solids
Drechslerová, V.; Neuhäuserová, M.; Falta, J.; Šleichrt, J.; Kytýř, Daniel
2023 - anglický
The aim of this paper is focused on benefits of stereolithography (SLA) technology for the fabrication of the lightweight lattice structures with potential for load-bearing function and high absorption of impact energy. SLA is an additive manufacturing technology employing the principle of liquid resins curing moderated by radiation of a wavelength from ultra-violet band where resulting material parameters are tunable by setting of the curing process. The batches of samples manufactured using three different resins were subjected to quasi-static uni-axial tensile and compression tests. Acquired data were processed to derive deformation behaviour expressed as stress-strain diagrams and fundamental material properties. Based on the knowledge obtained from the mechanical tests, the setup of the fabrication parameters, the most suitable resin for manufacturing of the lattice structures and the overall suitability of SLA technology for the fabrication of advanced porous materials, were determined.
Klíčová slova:
stereolithography; advanced porous materials; quasi-static testing; resin; mechanical characteristics
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Stereolithography for manufacturing of advanced porous solids
The aim of this paper is focused on benefits of stereolithography (SLA) technology for the fabrication of the lightweight lattice structures with potential for load-bearing function and high ...
A new blade cascade for flutter studies
Šnábl, Pavel; Pešek, Luděk; Procházka, Pavel P.; Skála, V.
2023 - anglický
In this paper, a new blade cascade, developed in the Institute of Thermomechanics, is presented. The geometry of the cascade was modified so now the stall flutter can occur. It has some major construction improvements over the original cascade which now allow more precise and reliable measurements. The stability of the new blade cascade with five NACA 0010 profiles with rotational degree of freedom is assessed by Travelling Wave Mode approach and Aerodynamic Influence Coefficient approach.
Klíčová slova:
blade cascade; stability; travelling wave mode; aerodynamic influence coefficient
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
A new blade cascade for flutter studies
In this paper, a new blade cascade, developed in the Institute of Thermomechanics, is presented. The geometry of the cascade was modified so now the stall flutter can occur. It has some major ...
Bohl-Marek decomposition applied to a class of biochemical networks with conservation properties
Papáček, Štěpán; Matonoha, Ctirad; Duintjer Tebbens, Jurjen
2023 - anglický
This study presents an application of one special technique, further called as Bohl-Marek decomposition, related to the mathematical modeling of biochemical networks with mass conservation properties. We continue in direction of papers devoted to inverse problems of parameter estimation for mathematical models describing the drug-induced enzyme production networks [3]. However, being aware of the complexity of general physiologically based pharmacokinetic (PBPK) models, here we focus on the case of enzyme-catalyzed reactions with a substrate transport chain [5]. Although our ultimate goal is to develop a reliable method for fitting the model parameters to given experimental data, here we study certain numerical issues within the framework of optimal experimental design [6]. Before starting an experiment on a real biochemical network, we formulate an optimization problem aiming to maximize the information content of the corresponding experiment. For the above-sketched optimization problem, the computational costs related to the two formulations of the same biochemical network, being (i) the classical formulation x˙(t) = Ax(t) + b(t) and (ii) the 'quasi-linear' Bohl-Marek formulation x˙M(t) = M(x(t)) xM(t), can be determined and compared.
Klíčová slova:
Mathematical modeling; Biochemical network; Pharmacokinetic (PBPK) models
Dokument je dostupný na externích webových stránkách.
Bohl-Marek decomposition applied to a class of biochemical networks with conservation properties
This study presents an application of one special technique, further called as Bohl-Marek decomposition, related to the mathematical modeling of biochemical networks with mass conservation properties. ...
Validation of numerical simulations of a simple immersed boundary solver for fluid flow in branching channels
Keslerová, R.; Lancmanová, Anna; Bodnár, Tomáš
2023 - anglický
This work deals with the flow of incompressible viscous fluids in a two-dimensional branching channel. Using the immersed boundary method, a new finite difference solver was developed to interpret the channel geometry. The numerical results obtained by this new solver are compared with the numerical simulations of the older finite volume method code and with the results obtained with OpenFOAM. The aim of this work is to verify whether the immersed boundary method is suitable for fluid flow in channels with more complex geometries with difficult grid generation.
Klíčová slova:
immersed boundary method; finite volume method; OpenFOAM
Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Validation of numerical simulations of a simple immersed boundary solver for fluid flow in branching channels
This work deals with the flow of incompressible viscous fluids in a two-dimensional branching channel. Using the immersed boundary method, a new finite difference solver was developed to interpret the ...
Rooting algebraic vertices of convergent sequences
Hartman, David; Hons, T.; Nešetřil, J.
2023 - anglický
Structural convergence is a framework for convergence of graphs by Nešetřil and Ossona de Mendez that unifies the dense (left) graph convergence and Benjamini-Schramm convergence. They posed a problem asking whether for a given sequence of graphs (Gn) converging to a limit L and a vertex r of L it is possible to find a sequence of vertices (rn) such that L rooted at r is the limit of the graphs Gn rooted at rn. A counterexample was found by Christofides and Král’, but they showed that the statement holds for almost all vertices r of L. We offer another perspective to the original problem by considering the size of definable sets to which the root r belongs. We prove that if r is an algebraic vertex (i.e. belongs to a finite definable set), the sequence of roots (rn) always exists.
Klíčová slova:
rooting; algebraic vertices; convergent sequences
Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Rooting algebraic vertices of convergent sequences
Structural convergence is a framework for convergence of graphs by Nešetřil and Ossona de Mendez that unifies the dense (left) graph convergence and Benjamini-Schramm convergence. They posed a problem ...
Effect of aging on mechanical properties of 3D printed samples using stereolithography
Drechslerová, V.; Falta, J.; Fíla, T.; Dvořák, R.; Kytýř, Daniel
2023 - anglický
This paper focuses on stereolithography (an additive manufacturing technology working on the principle of curing liquid resins layer by layer using ultraviolet radiation) and the effect of aging on the mechanical properties of the material and printed samples. The aging of the material could be a problem for its subsequent use as the stability of the mechanical properties would not be maintained and unwanted deterioration of the material could occur. As part of the research, sets of samples were printed and subjected to different aging methods and subsequently subjected to quasi-static and dynamic uni-axial load tests. From the data obtained, the basic mechanical properties of the material were calculated and compared with each other. The aim of this paper was to investigate whether aging process causes significant changes in the mechanical properties of the materials used, which could have a consequential impact on their use in different industries.
Klíčová slova:
stereolithography; aging; mechanical properties
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Effect of aging on mechanical properties of 3D printed samples using stereolithography
This paper focuses on stereolithography (an additive manufacturing technology working on the principle of curing liquid resins layer by layer using ultraviolet radiation) and the effect of aging on ...
Computed tomography system with strict real-time synchronization for in-situ 3D analysis of periodically vibrating objects
Rada, Václav; Fíla, Tomáš; Zlámal, Petr; Koudelka_ml., Petr; Šleichrt, Jan; Macháček, Michael; Vavřík, Daniel; Kytýř, Daniel
2023 - anglický
In the contribution, we present a laboratory system capable of X-ray computed tomography (XCT) scanning of an periodically moving or oscillating object. The system is an in-house developed XCT setup with electromagnetic voice coil actuator mounted on top of the rotary stage of the setup. The strict synchronization of the components, the rotary stage, the electromagnetic actuator movement and the detector readout is accomplished with use of the detector hardware trigger and hard real-time Linux operating system. Cylindrical sample manufactured from epoxy resin with metal particles to enable movement tracking is scanned in a stationary position and during periodical movement induced by the vibration stage. The volumetric data of the scans is compared and the results of this contribution represent an important step towards identification of defects through modal analysis of in-situ harmonically vibrating object.
Klíčová slova:
computed tomography; hardware trigger; harmonic motion; realtime synchronization
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Computed tomography system with strict real-time synchronization for in-situ 3D analysis of periodically vibrating objects
In the contribution, we present a laboratory system capable of X-ray computed tomography (XCT) scanning of an periodically moving or oscillating object. The system is an in-house developed XCT setup ...
Analysis suggestion for vehicle scanning method
Bayer, Jan
2023 - anglický
An analytical approach is suggested that can be conveniently applied in the framework of the Vehicle scanning method (VSM). It assumes that the modal parameters of a bridge will be imported from a finite element (FE) program into MATLAB, where the structural response caused by a moving mass and a moving spring mass is solved using coupling equations and numerical integration. A mathematical formulation of the solution is presented together with a short numerical case study that compares the results to a traditional closed form solution. It is shown that when comparing both forms of analysis the suggested approach is more accurate in the case of slow velocities of the passing sprung mass. Other advantages are that the method allows for the mass of the vehicle or (tractor) towing vehicle and a damping \nto be included in the calculation. The user-friendly preprocessing in commercial FE programs can also be considered an advantage.
Klíčová slova:
moving vehicle; vehicle scanning method; natural frequency; finite element analysis
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Analysis suggestion for vehicle scanning method
An analytical approach is suggested that can be conveniently applied in the framework of the Vehicle scanning method (VSM). It assumes that the modal parameters of a bridge will be imported from a ...
NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.
Vaše náměty a připomínky posílejte na email nusl@techlib.cz
Provozovatel
Zahraniční báze