Počet nalezených dokumentů: 1023
Publikováno od do

HYDROGEN STORAGE PROPERTIES OF GRAPHENE OXIDE MATERIALS PREPARED BY DIFFERENT WAYS
Král, Lubomír; Čermák, Jiří; Bytesnikova, Z.
2018 - anglický
Graphene-based materials show unique properties. These single layered materials consist of 2D structure of carbon atoms, belong to the strongest known materials, that are very mechanically flexible, optically transparent and that are excellent electrical and thermal conductors. Recently, several studies on these types of materials have highlighted the potential of this material for hydrogen storage (HS) and raised new hopes for the development of an effective solid-state HS media. In the present paper, the structure and HS properties of graphene oxide (GO) and chemically reduced graphene oxide (rGO) produced by different procedures were studied. Hydrogen sorption characteristics of GO and rGO were measured using the Sieverts-type gas sorption analyzer PCT-Pro Setaram Instrumentation. The study of HS was carried out at temperature range from 198 K to 423 K under hydrogen pressure from 1x10(-4) to 4 MPa. \n\nFor the HS point of view, the advantage of GO or rGO compared to graphene, is the presence of multiple chemical groups that can be used for introducing modifiers and their superior spreading on the materials surface. The suitably functionalized GO or rGO materials could potentially exhibit outstanding HS properties. Klíčová slova: Graphene oxide; hydrogen storage; adsorption; adsorption Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
HYDROGEN STORAGE PROPERTIES OF GRAPHENE OXIDE MATERIALS PREPARED BY DIFFERENT WAYS

Graphene-based materials show unique properties. These single layered materials consist of 2D structure of carbon atoms, belong to the strongest known materials, that are very mechanically flexible, ...

Král, Lubomír; Čermák, Jiří; Bytesnikova, Z.
Ústav fyziky materiálů, 2018

Estimation of mechanical parameters of thin films using finite element analysis
Tinoco Navaro, Hector Andres; Holzer, Jakub; Pikálek, Tomáš; Buchta, Zdeněk; Lazar, Josef; Chlupová, Alice; Kruml, Tomáš; Hutař, Pavel
2018 - anglický
This study shows a methodology to estimate mechanical parameters of thin films by means of a bulge\ntest and a numerical approach. The methodology is based on the combination of finite element analysis with a\nclassical analytical method. Finite element modelling was conducted for monolayer (Si3N4) membranes of 2x2mm\nwith the aim to approximate both the load-deflection curves experimentally measured and the classical loaddeflection\nanalytical model. Error functions were constructed and minimized to delimit a coupled solution space\nbetween Young’s modulus and Poison’s ratio. In a traditional bulge test analysis only one of the elastic properties\ncan be determined due to that there is not unique solution in the estimations of these parameters. However, both\nelastic parameters were determined through the proposed numerical procedure which compares the deformed\nsurfaces for a specific set of optimal elastic parameters computed. Results shows that the estimated elastic\nproperties agree with corresponding values determined by other methods in the literature Klíčová slova: bulge test; thin film; finite element analysis; elastic properties Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Estimation of mechanical parameters of thin films using finite element analysis

This study shows a methodology to estimate mechanical parameters of thin films by means of a bulge\ntest and a numerical approach. The methodology is based on the combination of finite element ...

Tinoco Navaro, Hector Andres; Holzer, Jakub; Pikálek, Tomáš; Buchta, Zdeněk; Lazar, Josef; Chlupová, Alice; Kruml, Tomáš; Hutař, Pavel
Ústav fyziky materiálů, 2018

CALIBRATION FUNCTIONS FOR EDGE CRACKS UNDER SELECTED BENDING LOADS.\n\n
Seitl, Stanislav; Miarka, Petr
2018 - anglický
Fatigue cracks are found during the regular structural inspections. To precisely\ndescribe/suggest of fatigue cracks propagation throughout structure and for designed\nservice life, the knowledge of calibration functions is important. The cracks usually\npropagate from the edge or the surface of the structural element. The theoretical model\nof fatigue crack propagation is based on linear fracture mechanics (Paris law). Steel\nstructural elements are subjected to various bending load (three- and four-point bending,\npure bending etc.). The calibration functions for the edge cracks are calculated for\nvarious load and appropriate polynomial function independent on the distance are\nproposed for 3PB and 4PB load. Klíčová slova: Fracture mechanics; calibration curve; stress intensity factor; Paris-Erdogan Law; edge Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
CALIBRATION FUNCTIONS FOR EDGE CRACKS UNDER SELECTED BENDING LOADS.\n\n

Fatigue cracks are found during the regular structural inspections. To precisely\ndescribe/suggest of fatigue cracks propagation throughout structure and for designed\nservice life, the knowledge of ...

Seitl, Stanislav; Miarka, Petr
Ústav fyziky materiálů, 2018

Evaluation of thin discontinuities in planar conducting materials using the diffraction of electromagnetic field
Savin, A.; Nový, F.; Fintová, Stanislava; Steigmann, R.
2017 - anglický
The current stage of nondestructive evaluation techniques imposes the development of new electromagnetic (EM) methods that are based on high spatial resolution and increased sensitivity. In order to achieve high performance, the work frequencies must be either radifrequencies or microwaves. At these frequencies, at the dielectric/conductor interface, plasmon polaritons can appear, propagating between conductive regions as evanescent waves. In order to use the evanescent wave that can appear even if the slits width is much smaller that the wavwelength of incident EM wave, a sensor with metamaterial (MM) is used. The study of the EM field diffraction against the edge of long thin discontinuity placed under the inspected surface of a conductive plate has been performed using the geometrical optics principles. This type of sensor having the reception coils shielded by a conductive screen with a circular aperture placed in the front of reception coil of emission reception sensor has been developed and 'transported' information for obtaining of magnified image of the conductive structures inspected. This work presents a sensor, using MM conical Swiss roll type that allows the propagation of evanescent waves and the electromagnetic images are magnified. The test method can be successfully applied in a variety of applications of maxim importance such as defect/damage detection in materials used in automotive and aviation technologies. Applying this testing method, spatial resolution can be improved. Klíčová slova: Electromagnetic fields; Electromagnetic wave reflection; Electromagnetic waves; Geometrical optics; Image resolution; Nondestructive examination; Testing Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Evaluation of thin discontinuities in planar conducting materials using the diffraction of electromagnetic field

The current stage of nondestructive evaluation techniques imposes the development of new electromagnetic (EM) methods that are based on high spatial resolution and increased sensitivity. In order to ...

Savin, A.; Nový, F.; Fintová, Stanislava; Steigmann, R.
Ústav fyziky materiálů, 2017

Effect of the load eccentricity on fracture behaviour of cementitious materials subjected to the modified compact tension test
Seitl, Stanislav; Ríos, J. D.; Cifuentes, H.; Veselý, V.
2017 - anglický
Fracture properties of quasi-brittle cementitious composites are typically determined from the load–displacement response recorded during a fracture test by using the work-of-fracture method or possibly other relevant fracture models. Our contribution is focused on a set of experimental tests which are used to study the fracture behaviour on notched dog-bone-shaped specimens made of cementitious materials. These specimens are subjected to modified compact tension (ModCT) test under a specific range of eccentricity of the tensile load. This type of test generates a stress state in the specimen ligament which combines a direct tension with a defined level of bending due to eccentricity of the tensile load. Several values of relative notch length are also considered. While the crack propagates, a variety of stress states, resulting in variations in the crack-tip stress and deformation constraint, appears in the ligament zone because of the changes in the eccentricity of the applied load, which influences the fracture behaviour of the investigated specimens. The K-calibration, T-stress, CMOD and COD curves for ModCT specimens are introduced and variations of these curves with varying load eccentricity are discussed. Klíčová slova: constraint; fracture; load accentricity Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Effect of the load eccentricity on fracture behaviour of cementitious materials subjected to the modified compact tension test

Fracture properties of quasi-brittle cementitious composites are typically determined from the load–displacement response recorded during a fracture test by using the work-of-fracture method or ...

Seitl, Stanislav; Ríos, J. D.; Cifuentes, H.; Veselý, V.
Ústav fyziky materiálů, 2017

Crack initiation in austenitic stainless steel sanicro 25 subjected to thermomechanical fatigue
Petráš, Roman; Škorík, Viktor; Polák, Jaroslav
2017 - anglický
Thermomechanical fatigue experiments were performed with austenitic stainless Sanicro 25 steel. Several amplitudes of mechanical strain in a wide temperature interval (250-700 °C) were applied to the specimens. Mechanical response was recorded and fatigue lives were obtained. Scanning electron microscopy combined with FIB technique was used to study the mechanism of crack initiation in in-phase and in out-of-phase thermomechanical cycling. Different mechanisms of the crack initiation were found in these two types of loading. During in-phase loading fatigue cracks start in grain boundaries by cracking of the oxide. Cracks grew preferentially along grain boundaries which resulted in rapid crack initiation and low fatigue life. In out-of-phase loading multiple cracks perpendicular to the stress axis developed only after sufficiently thick oxide layer was formed and cracked in low temperature loading half-cycle. The cracks in oxide allowed localized repeated oxidation and finally also cracking. The cracks grow transgranularly and result in longer fatigue life. Klíčová slova: Damage mechanism; FIB cutting; Localized oxidation-cracking; Sanicro 25 steel; Thermomechanical fatigue Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Crack initiation in austenitic stainless steel sanicro 25 subjected to thermomechanical fatigue

Thermomechanical fatigue experiments were performed with austenitic stainless Sanicro 25 steel. Several amplitudes of mechanical strain in a wide temperature interval (250-700 °C) were applied to the ...

Petráš, Roman; Škorík, Viktor; Polák, Jaroslav
Ústav fyziky materiálů, 2017

Lifetime Assessment of Particulate Ceramic Composite with Residual Stresses
Náhlík, Luboš; Majer, Zdeněk; Štegnerová, Kateřina; Hutař, Pavel
2017 - anglický
A micro-crack propagation in particulate ceramic based composite was studied using finite element method (FEM). Subcritical crack growth (SCG) was numerically simulated under complex load conditions (mechanical loading and loading by internal residual stresses). The effect of residual stresses on the crack propagation was studied. Two-dimensional computational model of particulate ceramic composite with material properties corresponding to low temperature co-fired ceramics (LTCC) was developed. The results indicate that the presence of residual stresses significantly reduces values of stress intensity factor in the vicinity of composite surface and the direction of residual stresses around the particles contributes to the micro-crack deflection from the particles. The time to failure of the composite under mechanical loading was determined. Results obtained contribute to a better understanding of the role of residual stresses during micro-crack propagation in ceramic particulate composites. Klíčová slova: ceramic particulate composite; sub-critical crack growth; residual stresses Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Lifetime Assessment of Particulate Ceramic Composite with Residual Stresses

A micro-crack propagation in particulate ceramic based composite was studied using finite element method (FEM). Subcritical crack growth (SCG) was numerically simulated under complex load conditions ...

Náhlík, Luboš; Majer, Zdeněk; Štegnerová, Kateřina; Hutař, Pavel
Ústav fyziky materiálů, 2017

Development of Creep Damage in Similar Weld Joints of P92 Steel Pipe
Král, Petr; Sklenička, Václav; Kuchařová, Květa; Svobodová, M.; Kvapilová, Marie; Dvořák, Jiří
2017 - anglický
The microstructure and creep behaviour of the welded joints of P92 steel pipe were\ninvestigated in order to determine the influence of orbital heat welding technology on the creep\nresistance. Creep specimens were machined from the welded joints. Tensile creep tests of welded\njoints were performed at 873 K using different stresses. The microstructure of tested specimens was\ninvestigated by scanning electron microscope Tescan equipped with an electron-back scatter\ndiffraction. The creep results showed that the creep fracture strain of the welded joints decreases\nwith decreasing value of applied stress. Microstructure investigation showed that fracture behaviour\nof welded joints is influenced by an enhanced cavity formation at grain boundaries in the heataffected\nzone causing lower fracture ductility. Klíčová slova: P92 steel; welding; creep damage; creep fracture; microstructure Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Development of Creep Damage in Similar Weld Joints of P92 Steel Pipe

The microstructure and creep behaviour of the welded joints of P92 steel pipe were\ninvestigated in order to determine the influence of orbital heat welding technology on the creep\nresistance. Creep ...

Král, Petr; Sklenička, Václav; Kuchařová, Květa; Svobodová, M.; Kvapilová, Marie; Dvořák, Jiří
Ústav fyziky materiálů, 2017

Influence of surface morphology on fatigue behavior of metastable austenitic stainless steel AISI 347 at ambient temperature and 300°C
Smaga, M.; Skorupski, R.; Mayer, P.; Kirsch, B.; Aurich, J. C.; Raid, I.; Seewig, J.; Man, Jiří; Eifler, D.; Beck, T.
2017 - anglický
The effect of surface modification by cryogenic turning on fatigue behavior of metastable austenitic stainless steel AISI 347 was investigated in stress-controlled fatigue tests at ambient temperature (AT) and 300 °C in air. Five different surface morphologies were manufactured by the variation of turning parameters. Surface and near surface morphology were comprehensively characterized by various experimental techniques. The experimental data on the cyclic deformation behavior, stress-strain response and fatigue life for all surface morphologies are reported. Klíčová slova: metastable austenitic stainless steel; cryogenic turning; fatigue; surface morphology; martensite Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Influence of surface morphology on fatigue behavior of metastable austenitic stainless steel AISI 347 at ambient temperature and 300°C

The effect of surface modification by cryogenic turning on fatigue behavior of metastable austenitic stainless steel AISI 347 was investigated in stress-controlled fatigue tests at ambient temperature ...

Smaga, M.; Skorupski, R.; Mayer, P.; Kirsch, B.; Aurich, J. C.; Raid, I.; Seewig, J.; Man, Jiří; Eifler, D.; Beck, T.
Ústav fyziky materiálů, 2017

Detekce plasticity v tenkých hliníkových vrstvách pomocí bulge testu
Holzer, Jakub; Pikálek, Tomáš; Buchta, Zdeněk; Lazar, Josef; Tinoco, H.A.; Chlupová, Alice; Náhlík, Luboš; Sobota, Jaroslav; Fořt, Tomáš; Kruml, Tomáš
2017 - anglický
The Bulge test proved to be a useful tool for measuring elastic properties of thin films and\nfree standing membranes, particularly Young’s modulus and residual stress. The basic principle\nof bulge test is application of differential pressure on one side of the a membrane, measurement of\nthe shape of bulged surface as a function of pressure, in this case via laser interferometer, and\nevaluation of a pressure-deflection relationship. In this study, bilayer membrane consisting of a\nsilicon nitride supporting layer and an aluminium layer deposited by means of magnetron\nsputtering is subjected to the bulge test. The results clearly show signs of a non-linear behavior\nthat is caused by plastic deformation in the aluminium layer. Finite element analysis is being\ndeveloped to describe this behavior because analytical model using deflection of central point and\npressure relation falls apart in case of non-linearity. Klíčová slova: Bulge test; thin films; mechanical test Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Detekce plasticity v tenkých hliníkových vrstvách pomocí bulge testu

The Bulge test proved to be a useful tool for measuring elastic properties of thin films and\nfree standing membranes, particularly Young’s modulus and residual stress. The basic principle\nof bulge ...

Holzer, Jakub; Pikálek, Tomáš; Buchta, Zdeněk; Lazar, Josef; Tinoco, H.A.; Chlupová, Alice; Náhlík, Luboš; Sobota, Jaroslav; Fořt, Tomáš; Kruml, Tomáš
Ústav fyziky materiálů, 2017

O službě

NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.

Vaše náměty a připomínky posílejte na email nusl@techlib.cz

Provozovatel

http://www.techlib.cz

Facebook

Zahraniční báze