No (3139)
Yes (81)
Number of found documents:
3220
Published from
to
Assessment of a report evaluating the impact analysis of the EDU II reactor unit power increase on the vertical stability and dynamic response of the internal parts of the reactor, including consideration of the LOCA DN500 event
Pták, Svatopluk
2023 - Czech
This technical report summarizes the results of the assessment aimed at evaluation of the impact analysis of the increase in the performance of EDU II units in connection with the project '6729 - Use of design margins of the Dukovany reactor units' on the vertical stability and dynamic response of the reactor internal components, including consideration of the LOCA DN500 event, specifically, it is an assessment of two reports of author collectives from ÚJV, a. s.: M. Klemenc and P. Gál: 'Analyzes of the impact of the power increase on the dynamic behavior of RIC during the LOCA DN500 event, report ÚJV DITI 2301/1242, 12/2020 and M. Švrček a J. Vyčichl: 'Analyzes of the impact of increasing power on vertical stability and vibration response (high-cycle fatigue) of RIC', report ÚJV DITI 2301/1307, 08/2021. Tato technická zpráva shrnuje výsledky posouzení výpočtové dokumentace zaměřené na hodnocení analýzy dopadu zvýšení výkonu bloků EDU II v souvislosti s projektem '6729 − Využití projektových rezerv bloků EDU II' na vertikální stabilitu a dynamickou odezvu vnitřních částí reaktoru včetně uvažování nehody LOCA DN500, konkrétně se jedná o posouzení dvou zpráv autorských kolektivů z ÚJV, a. s.: 'M. Klemenc a P. Gál: Analýzy dopadu zvýšení výkonu na dynamické chování VČR při nehodě LOCA DN500, zpráva ÚJV DITI 2301/1242, 12/2020' a M. Švrček a J. Vyčichl: Analýzy dopadu zvýšení výkonu na vertikální stabilitu a vibrační odezvu (vysokocyklovou únavu) VČR, zpráva ÚJV DITI 2301/1307, 08/2021.
Keywords:
loss coolant accident; dynamic response; primary pipelime of nuclear reactor; internal parts of nuclear reactor
Available at various institutes of the ASCR
Assessment of a report evaluating the impact analysis of the EDU II reactor unit power increase on the vertical stability and dynamic response of the internal parts of the reactor, including consideration of the LOCA DN500 event
This technical report summarizes the results of the assessment aimed at evaluation of the impact analysis of the increase in the performance of EDU II units in connection with the project '6729 - Use ...
Contract summary report OZM-LCF-2023: Experimental evaluation of low cycle fatigue properties of steel 1.4529
Štefan, Jan; Parma, Slavomír
2023 - Czech
This technical report was prepared within the framework of the contract "OZM-LCF-2023: Experimental evaluation of the properties of steel 1.4529 in terms of low cycle fatigue". The report clearly documents all relevant information concerning the technical performance of the contract, starting from the design of the experimental program, through the protocols of the experiments performed, to the summary evaluation of the program, including proposals for possible contract extension and follow-up experimental activities. Tato technická zpráva byla zpracována v rámci zakázky „OZM-LCF-2023: Experimentální hodnocení vlastností oceli 1.4529 z hlediska nízkocyklové únavy“. Ve zprávě jsou přehledně zdokumentovány všechny podstatné informace týkající se odborného plnění zakázky počínaje návrhem experimentálního programu, přes protokoly o provedených experimentech až po souhrnné vyhodnocení programu vč. návrhů pro případné rozšíření zakázky a navazující experimentální činnost.
Keywords:
material testing; low-cycle fatigue; austenitic stainless steels
Available at various institutes of the ASCR
Contract summary report OZM-LCF-2023: Experimental evaluation of low cycle fatigue properties of steel 1.4529
This technical report was prepared within the framework of the contract "OZM-LCF-2023: Experimental evaluation of the properties of steel 1.4529 in terms of low cycle fatigue". The report clearly ...
Measurements on KR-D-11B Optimized Subsonic Blade Cascade
Šimurda, David; Hála, Jindřich
2023 - English
This report contains results and evaluation of aerodynamic measurements conducted on a subsonic compressor blade cascade.
Keywords:
compressor blade cascade; experiment; subsonic flow; optimized profile
Available at various institutes of the ASCR
Measurements on KR-D-11B Optimized Subsonic Blade Cascade
This report contains results and evaluation of aerodynamic measurements conducted on a subsonic compressor blade cascade.
Dynamics of Machines and Mechanical Systems with Interactions, DYMAMESI 2023
Zolotarev, Igor; Pešek, Luděk; Kozień, M. S.
2023 - English
The aim of the DYMAMESI is to facilitate the exchange of up to date information and knowledge among specialists in structural and multibody dynamics, in coupled interacting systems as aero-elasticity, hydro-elasticity, biomechanics, systems with feedbacks and mechatronics. The colloquium DYMAMESI 2021 is cofunded by the Strategy AV21 initiative of the Czech Academy of Sciences of the Czech Republic, and in 2021 will be hosted by Cracow University of Technology, Institute of Applied Mechanics, Section of Dynamics of Systems.
Keywords:
dynamics; vibrations of mechanical systems; vibrodiagnostics; energy transformations
Available at various institutes of the ASCR
Dynamics of Machines and Mechanical Systems with Interactions, DYMAMESI 2023
The aim of the DYMAMESI is to facilitate the exchange of up to date information and knowledge among specialists in structural and multibody dynamics, in coupled interacting systems as aero-elasticity, ...
Final report on the MIT project no. CZ.01.1.02/0.0/0.0ú20_321/0023673
Zolotarev, Igor; Pešek, Luděk; Gabriel, Dušan; Procházka, Pavel P.
2023 - Czech
The MIT project entitled Development of a switchgear for severe conditions and reduction of risks of critical infrastructure threat was focused on research, development of optimized design and provision of configuration technology for repeated production of different variants of modular system switchgear for use in severe conditions and reduction of risks of seismic threat, to ensure the reliability of critical infrastructure. The output is to be a prototype seismically robust device with a dynamically lightweight design, high reliability of switchgear and electrical equipment assembly function, and a software application for interactive design and documentation. Projektu MPO s názvem Vývoj rozvaděče pro těžké podmínky a snížení rizik ohrožení kritické infrastruktury byl zaměřen na výzkum, vývoj optimalizované konstrukce a zajištění konfigurační technologie pro opakovanou produkci různých variant modulárního systémového rozváděče pro použití v těžkých podmínkách a snížení rizik seizmického ohrožení, pro zajištění spolehlivosti kritické infrastruktury. Výstupem má být prototyp seizmicky robustního zařízení s dynamicky odlehčené konstrukce, vysokou spolehlivostí funkce sestavy rozvaděče a elektrovýzbroje a SW aplikace pro interaktivní návrhy a dokumentaci.
Keywords:
vibration; natural frequencies; modes of vibration; seismic resistance; dynamic properties of structures
Available at various institutes of the ASCR
Final report on the MIT project no. CZ.01.1.02/0.0/0.0ú20_321/0023673
The MIT project entitled Development of a switchgear for severe conditions and reduction of risks of critical infrastructure threat was focused on research, development of optimized design and ...
Comparison of finite element simulation of tungsten nanoindentation with Berkovich and conical indenter
Fiala, L.; Ballo, I.; Kovář, J.; Fuis, Vladimír
2023 - English
Finite Element Method (FEM) was used to study the difference between using Berkovich and conical indenters in nanoindentation test of tungsten specimen. The study was aimed to determine the\nmodulus of elasticity of a tested specimen and how it changes with different indenter. The FEM analysis also revealed that the modulus of elasticity was sensitive to the dimensions of both specimen and the indenter for which were made several numerical calculations with different dimensions.
Keywords:
nanoindentation; FEM; Berkovich indenter; conical indenter; tungsten
Available at various institutes of the ASCR
Comparison of finite element simulation of tungsten nanoindentation with Berkovich and conical indenter
Finite Element Method (FEM) was used to study the difference between using Berkovich and conical indenters in nanoindentation test of tungsten specimen. The study was aimed to determine the\nmodulus ...
Asynchronous time integration while achieving zero interface energy
Dvořák, Radim; Kolman, Radek; Falta, J.; Neühauserová, M.
2023 - English
This contribution deals with an asynchronous direct time integration of the finite-element model. The proposed method is applied to the phenomenon of wave propagation through an elastic linear continuum. The numerical model is partitioned into individual subdomains using the domain decomposition method by means of localized Lagrange multipliers. For each subdomain, different time discretizations are used. No restrictions for relation between subdomain’s time steps are imposed. The coupling of the subdomains is forced by an acceleration continuity condition. Additionally, we use the a posteriori technique to also provide the displacement and velocity continuity at the interfaces, and hence we obtain exact continuity of all three kinematic fields. The proposed method is experimentally validated using the modified SHPB (split Hopkinson pressure bar) setup.
Keywords:
finite element method; direct time integration; asynchronous integration; domain decomposition; localized lagrange multipliers
Available at various institutes of the ASCR
Asynchronous time integration while achieving zero interface energy
This contribution deals with an asynchronous direct time integration of the finite-element model. The proposed method is applied to the phenomenon of wave propagation through an elastic linear ...
Optical and Pneumatic Measurements on TR-U-11 Cascade
Luxa, Martin; Hála, Jindřich; Šimurda, David
2023 - English
The report contains results and evaluation of conducted optical (interferometry and schlieren technique) and pneumatic measurements on the first variant of the new tip section, intended for turbine rotor blade.
Keywords:
transonic flow; rotor turbine blade; tip section
Available at various institutes of the ASCR
Optical and Pneumatic Measurements on TR-U-11 Cascade
The report contains results and evaluation of conducted optical (interferometry and schlieren technique) and pneumatic measurements on the first variant of the new tip section, intended for turbine ...
A new blade cascade for flutter studies
Šnábl, Pavel; Pešek, Luděk; Procházka, Pavel P.; Skála, V.
2023 - English
In this paper, a new blade cascade, developed in the Institute of Thermomechanics, is presented. The geometry of the cascade was modified so now the stall flutter can occur. It has some major construction improvements over the original cascade which now allow more precise and reliable measurements. The stability of the new blade cascade with five NACA 0010 profiles with rotational degree of freedom is assessed by Travelling Wave Mode approach and Aerodynamic Influence Coefficient approach.
Keywords:
blade cascade; stability; travelling wave mode; aerodynamic influence coefficient
Available at various institutes of the ASCR
A new blade cascade for flutter studies
In this paper, a new blade cascade, developed in the Institute of Thermomechanics, is presented. The geometry of the cascade was modified so now the stall flutter can occur. It has some major ...
Thermal and creep analysis of VVER-1000 reactor pressure vessel at high temperatures caused by fuel melting during severe accident
Gabriel, Dušan; Gál, P.; Kotouč, M.; Dymáček, Petr; Masák, Jan; Kopačka, Ján
2023 - English
Thermal and creep analysis of the VVER-1000 reactor pressure vessel (RPV) was performed at high temperatures caused by fuel melting during severe accident. First, the integral code ASTEC was applied simulating severe accident evolution since an initiating event up to a hypothetical radioactive release into the environment. The ASTEC outputs including the remaining RPV wall thickness, the heat flux achieved and the temperature profile in the ablated vessel wall served as boundary conditions for the consequent assessment of RPV integrity carried out with the aid of finite element method (FEM). The FEM analysis was performed including the creep behaviour of RPV material using a complex creep probabilistic exponential model with damage. The objective of the analysis was to computationally assess emergency condition and, on this basis, to propose a general methodology for evaluating the integrity of RPV at high temperatures due to fuel melting during severe accident.
Keywords:
integrity of reactor pressure vessel; severe accident; ASTEC; creep; FEM
Fulltext is available at external website.
Thermal and creep analysis of VVER-1000 reactor pressure vessel at high temperatures caused by fuel melting during severe accident
Thermal and creep analysis of the VVER-1000 reactor pressure vessel (RPV) was performed at high temperatures caused by fuel melting during severe accident. First, the integral code ASTEC was applied ...
NRGL provides central access to information on grey literature produced in the Czech Republic in the fields of science, research and education. You can find more information about grey literature and NRGL at service web
Send your suggestions and comments to nusl@techlib.cz
Provider
Other bases