Počet nalezených dokumentů: 988
Publikováno od do

The effect of the backfill on the integrity of a buried pipeline upon heavy-duty vehicle crossings
Gajdoš, Lubomír; Šperl, Martin; Slížková, Zuzana; Drdlová, M.
2023 - anglický
The aim of this work was to determine stresses in the wall of a buried empty gas pipeline caused by the weight of backfill as well as by heavy-duty vehicles crossing the pipeline, and, on their basis to assess the applicability of protective sleeves. A buried pipeline with zero internal pressure of transported medium (empty pipeline) differs from an unburied pipeline by the vertical load due to the weight of the backfill which causes an ovalness of the circular cross section of the pipeline. This leads to the rise of through-wall bending stresses with the tensile stress at the outside surface at the 3 and 9 o´clock positions and compressive stress at the inside surface. At the 6 and 12 o´clock positions the stresses are tensile at the inside surface and compressive at the outside surface. The current depth of soil cover above gas pipelines is 0.5 m. For pipes DN500, t ~ 6.5 mm the through-wall bending stress is found to be σb ≈ ±10 MPa. In comparison with the yield stress of pipeline material, this stress is negligible. The situation is changed when heavy-duty vehicles cross the pipeline. For example, when a MAN truck with the mass load 3270 kg acting on a single wheel of the front axle crosses this pipeline, the pressure transmitted to the pipe will cause the through-wall bending stress σb ≈ ±76 MPa. This stress is superimposed to that of the backfill to give the total value ±86 MPa. When dead loads, imposed by backfill cover, together with live loads, caused by truck-wheel loads, are excessive a crushing of side walls of the pipeline and/or ring buckling of the pipe cross section can happen. Klíčová slova: gas pipeline; pressure; buried pipeline Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
The effect of the backfill on the integrity of a buried pipeline upon heavy-duty vehicle crossings

The aim of this work was to determine stresses in the wall of a buried empty gas pipeline caused by the weight of backfill as well as by heavy-duty vehicles crossing the pipeline, and, on their basis ...

Gajdoš, Lubomír; Šperl, Martin; Slížková, Zuzana; Drdlová, M.
Ústav teoretické a aplikované mechaniky, 2023

Experimental evaluation of aluminothermic welds
Zeman, L.; Valach, J.; Zlámal, P.; Krčmářová, N.; Koudelková, Veronika; Zeman, J.
2023 - anglický
The article presents a study of the mechanical processes occurring during the aluminother-mic reaction using experimental methods (strain gauges, digital image correlation, thermography,scanning electron microscopy, profilometry). The aluminothermic reaction is a highly efficient weldingmethod due to its exothermic behaviour, however, it places considerable demands not only on thewelding technique, but also on the capabilities of the experimental methods used - these limitationsare also discussed in the article. The aluminothermic reaction is associated with the formation of alocalised heat source with a time evolution dictated by the technological procedure, which manifestsitself in heat propagation to the surrounding weld material. The unequal evolution of the temperaturefield is the fundamental cause of the appearance of the heat affected zone or local deformations orsurface curvature, which was the focus of the experimental methods deployed above and the results ofwhich are shown in the article. Klíčová slova: aluminothermic reaction; train gauges; hardness; profilometry; scanning electron microscope Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Experimental evaluation of aluminothermic welds

The article presents a study of the mechanical processes occurring during the aluminother-mic reaction using experimental methods (strain gauges, digital image correlation, thermography,scanning ...

Zeman, L.; Valach, J.; Zlámal, P.; Krčmářová, N.; Koudelková, Veronika; Zeman, J.
Ústav teoretické a aplikované mechaniky, 2023

Analyzing stochastic stability of a gyroscope through the stochastic Lyapunov function
Náprstek, Jiří; Fischer, Cyril
2023 - anglický
The text delves into the application of first integrals in the construction of Lyapunov functions for analyzing the stability of dynamic systems in stochastic domains. It emphasizes the distinct characteristics of first integrals that warrant the introduction of additional constraints to ensure the essential properties required for a Lyapunov function. These constraints possess physical interpretations associated with system stability. The general approach to testing stochastic stability is illustrated using the example of a 3-degrees-of-freedom system representing a gyroscope. Klíčová slova: stochastic stability; Lyapunov function; first integral; gyroscope Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Analyzing stochastic stability of a gyroscope through the stochastic Lyapunov function

The text delves into the application of first integrals in the construction of Lyapunov functions for analyzing the stability of dynamic systems in stochastic domains. It emphasizes the distinct ...

Náprstek, Jiří; Fischer, Cyril
Ústav teoretické a aplikované mechaniky, 2023

Conductive open-cell silicone foam for modulatable damping and impact sensing applications
Preuer, R.; Šleichrt, Jan; Kytýř, Daniel; Graz, I.
2023 - anglický
Nature has long served as a source of inspiration for the development of new materials, with foam-like structures in fruits such as oranges and pamelos serving as examples of efficient energy dissipation. In this study, we present the synthesis and characterization of a conductive silicone foam for potential impact sensing applications. By blending Sylgard 184 and Carbon Black, we create a highly porous structure capable of dissipating energy and modulating its resistance. To investigate the properties of the foam, we utilized both micro-computer tomography (μCT) and scanning electron microscopy (SEM) imaging techniques. The μCT imaging revealed the intricate pore network of the foam, reminiscent of the complex structure found in natural sponges. SEM imaging allowed for observation of the uniform distribution of Carbon Black particles within the foam, enabling the conductive properties of the foam. The foam’s mechanical behavior was characterized by a compression test under μCT imaging to measure the deformation behavior and changes in the foam’s resistance. Additionally, a ball drop test was conducted to investigate the foam’s damping behavior while simultaneously measuring the impact location by the local change in resistance. Remarkably, our results demonstrate the exceptional damping capabilities of the conductive silicone foam, with the damping ratio modulated by adjusting the degree of compression-induced deformation. This is attributed to the collapse of the foam’s porous structure, resulting in a significant increase in the foam’s contact area. Overall, our study provides valuable insights into the behavior of conductive silicone foams and their potential as an impact sensing material. The use of both CT and SEM imaging techniques allows for a comprehensive understanding of the foam’s properties, which can be optimized for a variety of applications. The foam’s ability to modulate its damping properties by adjusting the degree of deformation provides a promising avenue for future research in the field of materials science and engineering. Klíčová slova: silicone foam; conductive properties; deformation behaviour; damping Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Conductive open-cell silicone foam for modulatable damping and impact sensing applications

Nature has long served as a source of inspiration for the development of new materials, with foam-like structures in fruits such as oranges and pamelos serving as examples of efficient energy ...

Preuer, R.; Šleichrt, Jan; Kytýř, Daniel; Graz, I.
Ústav teoretické a aplikované mechaniky, 2023

Fast continuous in-situ XCT of additively manufactured carbon fiber reinforced tensile test specimens
Glinz, J.; Maurer, J.; Holzleitner, M.; Pace, F.; Stamopoulos, A.; Vopálenský, Michal; Kumpová, Ivana; Eckl, M.; Kastner, J.; Senck, S.
2023 - anglický
The reinforcement of fused filament fabricated (FFF) components with continuous fibers allows for high versatility in the design of mechanical properties for a specific application’s needs. However, the bonding quality between continuous fibers and the FFF matrix material has high impact on the overall performance of the composite. In a recent study [1], additively manufactured (AM) continuous fiber reinforced tensile test specimens have been investigated regarding the effect of amount and material of the embedded continuous fibers on tensile strength and AM build quality. During these tensile tests, a sudden reduction in tensile stress, which most likely was not related to actual rupture of continuous fibers, was noticeable. Since X-ray computed tomography (XCT) scans were performed only prior to and after the tensile testing, a detailed investigation on the origin of these drops in tensile stress was not possible. Within this work, we will expand upon these findings and present results of fast on-the-fly in-situ investigations performed on continuous carbon fiber reinforced specimens of the same AM build. During these investigations, specimens are loaded under the same conditions while fast XCT scans, with a total scan time of 12 seconds each, were performed consecutively. The resulting three-dimensional image data reveals internal meso- and macro-structural changes over time/strain to find the cause of the aforementioned reduction in tensile stress. Klíčová slova: additive manufacturing; composites; X-ray computed tomography; in-situ tensile testing Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Fast continuous in-situ XCT of additively manufactured carbon fiber reinforced tensile test specimens

The reinforcement of fused filament fabricated (FFF) components with continuous fibers allows for high versatility in the design of mechanical properties for a specific application’s needs. However, ...

Glinz, J.; Maurer, J.; Holzleitner, M.; Pace, F.; Stamopoulos, A.; Vopálenský, Michal; Kumpová, Ivana; Eckl, M.; Kastner, J.; Senck, S.
Ústav teoretické a aplikované mechaniky, 2023

Innovative device for the simulation of environmental conditions and testing of building materials
Cacciotti, Riccardo; Wolf, Benjamin; Macháček, Michael; Frankl, Jiří
2022 - anglický
Excessive humidity influences the performance of building envelopes and the safety of their occupants. Moisture related problems can indeed impose significant health risks for buildings’ users and even lead, under extreme scenarios, to structural failures. This paper investigates an innovative experimental setup for evaluating the influence of changing environmental conditions on the performance of building materials. It stems out from a broader ongoing research aimed at studying the trends of mould growth on wooden building components. The presented results include the design, construction and numerical validation of a small-scale climatic wind tunnel (2m x 1.8m ca.) to be used for the simulation of natural ventilation and daily humidity and temperature fluctuations. Key findings include the final design of a low cost, modular construction which allows gathering reliable data on the response of building materials exposed to changing boundary conditions, intended for improving current mould growth models. Future work is also suggested. Klíčová slova: building envelope; moisture; building material; wind tunnel; performance Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Innovative device for the simulation of environmental conditions and testing of building materials

Excessive humidity influences the performance of building envelopes and the safety of their occupants. Moisture related problems can indeed impose significant health risks for buildings’ users and ...

Cacciotti, Riccardo; Wolf, Benjamin; Macháček, Michael; Frankl, Jiří
Ústav teoretické a aplikované mechaniky, 2022

Application of first integrals in the construction of the Lyapunov function for the random response stability testing
Náprstek, Jiří; Fischer, Cyril
2022 - anglický
The paper deals with a possibility of using the properties of first integrals for the construction of Lyapunov function for the analysis of a dynamic system stability in the stochastic domain. It points out certain characteristics of first integrals resulting in the necessity to introduce additional constraints to assure the principal properties of the Lyapunov function. A number of these constraints has their physical interpretation with reference to system stability. The advantage of this method constructing the Lyapunov function consists in the fact that the Lyapunov function itself contains information on the examined system and, consequently, it is not merely a positive definite function without any relation to the actual case concerned. The presented theory finds application in many dynamical systems. The procedure is illustrated by a nonlinear SDOF example. Klíčová slova: stochastic stability; Lyapunov function; first integrals; cyclic coordinates Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Application of first integrals in the construction of the Lyapunov function for the random response stability testing

The paper deals with a possibility of using the properties of first integrals for the construction of Lyapunov function for the analysis of a dynamic system stability in the stochastic domain. It ...

Náprstek, Jiří; Fischer, Cyril
Ústav teoretické a aplikované mechaniky, 2022

Determination of aerodynamic coefficients for air flow around U-profiles with different flange porosities
Ledvinková, Blanka; Hračov, Stanislav; Macháček, Michael
2022 - anglický
Our contribution presents the comparison of the experimental investigations and of the numerical 2D simulations of the air flow around U –profiles having different flange porosities. The U-shaped beams were exposed to the air flow having a given velocity at different angles of the wind attack for obtaining the curves of the aerodynamic coefficients depending on the impact angle. The numerical simulations of the wind tunnel testing were performed using the Unsteady Reynolds Averaged Navier-Stokes (RANS) method, k-ω SST turbulence model was assumed. Klíčová slova: U-shaped beams; porosity; wind tunnel; RANS simulation; k-ω SST model Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Determination of aerodynamic coefficients for air flow around U-profiles with different flange porosities

Our contribution presents the comparison of the experimental investigations and of the numerical 2D simulations of the air flow around U –profiles having different flange porosities. The U-shaped ...

Ledvinková, Blanka; Hračov, Stanislav; Macháček, Michael
Ústav teoretické a aplikované mechaniky, 2022

Theoretical analysis of selected trajectories inscribed by a ball freely rolling in a spherical cavity
Náprstek, Jiří; Fischer, Cyril
2022 - anglický
Indirect monitoring of structures is significantly complicated when an artificial vibration absorber has to be taken into account. Knowledge of the absorber’s behaviour is necessary in order to correctly distinguish the response types obtained during an drive-by measurement. In this work, the mathematical model of the ball-type vibration absorber is used, which is based on the Lagrangian formalism. Three first integrals are identified when no external excitation nor damping is assumed. The paper illustrates the power of this approach, which enables a detailed analysis of free movement of the ball in the spherical cavity. Properties of several particular trajectories depending on initial conditions are presented. Klíčová slova: slender structure; vibration absorber; first integral; rolling sphere; structural health monitoring Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Theoretical analysis of selected trajectories inscribed by a ball freely rolling in a spherical cavity

Indirect monitoring of structures is significantly complicated when an artificial vibration absorber has to be taken into account. Knowledge of the absorber’s behaviour is necessary in order to ...

Náprstek, Jiří; Fischer, Cyril
Ústav teoretické a aplikované mechaniky, 2022

Long term optical monitoring technique of displacement fields based on ArUco markers
Kunecký, Jiří
2022 - anglický
In structural engineering it is often needed to measure tiny displacements of parts of the structure extremely precisely. For such a purpose it is often needed to use some type of sensor attached to the surface of the structure. This paper presents a new technique which simply uses computer vision libraries to measure displacement of markers originally developed for robotics. Such analysis can be under specific circumstances (2D planar movement) valid if we compare two images taken at different times with the same camera. Main advantage of this method is simplicity of use and low cost of markers, which can be printed in a standard office laser printer. The resolution (error) can be for standard cameras around 0.1 pixel. The method is especially developed for research of timber frames/joints behavior in real structures, because displacements of joints in creep or under load can reach an amplitude which is perfectly detectable by this method. Klíčová slova: displacement measurement; long-term monitoring; ArUco markers Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Long term optical monitoring technique of displacement fields based on ArUco markers

In structural engineering it is often needed to measure tiny displacements of parts of the structure extremely precisely. For such a purpose it is often needed to use some type of sensor attached to ...

Kunecký, Jiří
Ústav teoretické a aplikované mechaniky, 2022

O službě

NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.

Vaše náměty a připomínky posílejte na email nusl@techlib.cz

Provozovatel

http://www.techlib.cz

Facebook

Zahraniční báze