Ne (12587)
Ano (2276)
Počet nalezených dokumentů:
14863
Publikováno od
do
Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding
Šebestová, Hana; Horník, Petr; Mika, Filip; Mikmeková, Šárka; Ambrož, Ondřej; Mrňa, Libor
2024 - anglický
Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. When the coated sheets are welded, the effect of the chemical composition of the coating must be also considered even though its thickness is only a few tens of microns. During 22MnB5+AlSi laser welding experiments, the ferrite-stabilizing elements of coating modified the weld metal microstructure. Ferrite appeared in a quenched weld metal. The rapid cooling rate accompanying welding with a focused beam limited the homogenization of the weld metal which resulted in the formation of ferritic bands in the regions rich in Si and especially in Al. On the other hand, a high level of homogenization was reached when welding with the defocused beam. The ferritic islands uniformly distributed in the weld metal were formed at 0.4 wt% and 1.6 wt% of Si and Al, respectively. The doubled heat input reduced the Al content to 0.7 wt% insufficient for the ferrite formation at still relatively high cooling rates. Predicting the distribution of ferrite in the weld metal is challenging due to its dependence on various factors, such as cooling rate and the volume of dissolved coating, which may vary with any modifications made to the welding parameters.
Klíčová slova:
laser welding; high-strength steel; microstructure; heat input; ferrite stabilization
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Microstructure modifications of Al-Si-coated press-hardened steel 22MnB5 by laser welding
Weld microstructure depends on the characteristics of welded materials and parameters of welding technology, especially on the heat input that determines the peak temperature and the cooling rate. ...
Finite element approximation of fluid structure interaction using Taylor-Hood and Scott-Vogelius elements
Vacek, Karel; Sváček, P.
2024 - anglický
This paper addresses the problem of fluid flow interacting a vibrating solid cylinder described by one degree of freedom system and with fixed airfoil. The problem is described by the incompressible Navier-Stokes equations written in the arbitrary Eulerian-Lagrangian (ALE) formulation. The ALE mapping is constructed with the use of a pseudo-elastic approach. The flow problem is numerically approximated by the finite element method (FEM). For discretization of the fluid flow, the results obtained by both the Taylor-Hood (TH) element and the Scott-Vogelius (SV) finite element are compared. The TH element satisfies the Babuška-Brezzi inf-sup condition, which guarantees the stability of the scheme. In the case of the SV element the mesh, that is created as a barycentric refinement of regular triangulation, is used to satisfy the Babuška-Brezzi condition. The numerical results for two benchmark problems are shown.
Klíčová slova:
finite element method; arbitrary Lagrangian-Eulerian method; Scott-Vogelius element; Taylor-Hood element
Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Finite element approximation of fluid structure interaction using Taylor-Hood and Scott-Vogelius elements
This paper addresses the problem of fluid flow interacting a vibrating solid cylinder described by one degree of freedom system and with fixed airfoil. The problem is described by the incompressible ...
Surfactant-free silver nanofluids as liquid systems with neuromorphic potential
Nikitin, D.; Biliak, K.; Lemke, J.; Protsak, M.; Pleskunov, P.; Tosca, M.; Ali-Ogly, S.; Červenková, V.; Adejube, B.; Bajtošová, L.; Černochová, Zulfiya; Prokeš, J.; Křivka, I.; Biederman, H.; Faupel, F.; Vahl, A.; Choukourov, A.
2024 - anglický
Neuromorphic engineering is a rapidly developing branch of science that aims to implement the unique attributes of biological neural networks in artificial devices. Most neuromorphic devices are based on the resistive switching effect, which involves changing the device’s conductivity in response to an external electric field. For instance, percolating nanoparticle (NP) networks produced by gas aggregation cluster sources (GAS) show collective spiking behavior in conductivity reminiscent of brain-like dynamics. Nevertheless, the problem of dynamic spatial reconfiguration in solid-state neuromorphic systems remains unsolved. Herein, novel nanofluids with resistive switching properties are proposed as neuromorphic media. They are produced by depositing silver NPs from GAS into vacuum-compatible liquids (paraffin, silicon oil, and PEG) without the use of surfactants or other chemicals. When the electric field is applied between two electrodes, the migration of NPs toward biased electrode is detected in all liquids. The electrophoretic nature of the NP movement was proved by means of ζ-potential measurements. Such movement led to the self-assembly of NPs in conductive paths connecting the electrodes and, as a result, to resistive switching. The electrical response was strongly dependent on the dielectric constant of the base liquid. The Ag-PEG nanofluid demonstrated the best switching performance reproducible during several tens of current-voltage cycles. The growth of flexible and reconfigurable conductive filaments in nanofluids makes them suitable media for potential realization of 3D neural networks.
Klíčová slova:
nanofluid; gas aggregation cluster source; ζ-potential, electrophoresis
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Surfactant-free silver nanofluids as liquid systems with neuromorphic potential
Neuromorphic engineering is a rapidly developing branch of science that aims to implement the unique attributes of biological neural networks in artificial devices. Most neuromorphic devices are based ...
Flow simulations approach for flocculation tanks
Idžakovičová, Kristýna; Bílek, Vojtěch; Haidl, Jan; Isoz, M.; Pivokonský, Martin
2024 - anglický
Flocculation in water treatment facilities plays a key role in the separation of colloidal inorganic and organic substances. Its optimization leads to a significant increase in its efficiency and savings of operational costs. However, it is currently based on trial-and-error experimental approaches. In this contribution, we focus on flow modeling in stirred flocculation tanks that would, after coupling with a calibrated model of particle aggregation, enable simulationbased flocculation optimization. Despite the abundance of literature on stirred tank modeling, there is no universal agreement on the methodology used to describe turbulence nor on the approach to the computational mesh creation. Consequently, there is no unified methodology for simulations and their validation. To address this, we present a best-practice methodology for economical, yet reliable flow simulations in the said device. This methodology includes the choice of the turbulence model, the approach to the design of a high quality mesh suitable for arbitrary geometries, and results evaluation. It is developed based on an extensive literature review, a multitude of flow simulations using several meshes of progressively higher quality and resolution, and various strategies to converge to steady-state flow conditions. The simulation quality indicators used here involve comparison with the experimental data on fluid velocity, stirrer power output, and flow rate through the impeller zone. Additionally, the resulting flow simulation models are compared using tracer transport simulations, hinting at their potential for coupling with particle aggregation models.
Klíčová slova:
flocculation tank; stirring; MRF; CFD; OpenFOAM
Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Flow simulations approach for flocculation tanks
Flocculation in water treatment facilities plays a key role in the separation of colloidal inorganic and organic substances. Its optimization leads to a significant increase in its efficiency and ...
Galloping of insulated bundled overhead line - nonlinear numerical analysis in time domain
Macháček, Michael; Hračov, Stanislav
2024 - anglický
Our contribution focuses on a 3D numerical nonlinear analysis of galloping in a specific bundled overhead line with ice accretion. We studied the susceptibility to this self-excited oscillation, critical onset wind speeds, and global dynamic response of a very low-tensioned line with simulated icing observed on similar real conductors. Due to the highly nonlinear mechanical behavior of such a flexible cable, we employed the Newmark integration method combined with the iterative Newton-Raphson method. We analyzed two numerical models of the overhead line loaded by the wind: one assuming nonlinearity only in the wind load, while retaining the linearity of the mechanical system itself, and the other representing a fully nonlinear system including geometrical nonlinearity. Our analysis revealed that the determined critical wind speeds for the onset of galloping are in relatively close ranges for both models. However, numerical simulations with the fully nonlinear system indicated significantly lower amplitudes of limit cycle oscillations, especially at higher wind speeds, compared to the linear model of the line. This underscores the necessity of using fully nonlinear models during the design stage of such low-tensioned aerial conductors.
Klíčová slova:
aerial bundled conductors; wind effects; galloping; limit cycle oscillation
Plné texty jsou dostupné v digitálním repozitáři Akademie Věd.
Galloping of insulated bundled overhead line - nonlinear numerical analysis in time domain
Our contribution focuses on a 3D numerical nonlinear analysis of galloping in a specific bundled overhead line with ice accretion. We studied the susceptibility to this self-excited oscillation, ...
Electrochemical Properties of Pretomanid. New drug for Tuberculosis Treatment
Deri, M.; Vespi, M.; Giannarelli, S.; Hromadová, Magdaléna
2024 - anglický
The electrochemical behavior of Pretomanid (PA 824) has been investigated in acetonitrile by cyclic voltammetry at different scan rates and compared to dimetridazole reduction in order to elucidate its redox mechanism. Both compounds show similar reduction behavior in the aprotic solvent that involves one electron transfer to the nitro group. The reduction of Pretomanid is more difficult and the stability of its nitro anion radical is much lower compared to the dimetridazole molecule.
Klíčová slova:
pretomanid; dimetridazole; cyclic voltammetry; reduction mechanism
Plné texty jsou dostupné na vyžádání prostřednictvím repozitáře Akademie věd.
Electrochemical Properties of Pretomanid. New drug for Tuberculosis Treatment
The electrochemical behavior of Pretomanid (PA 824) has been investigated in acetonitrile by cyclic voltammetry at different scan rates and compared to dimetridazole reduction in order to elucidate ...
Redox Properties of Pyrene-Cyclohexene Conjugates – Electrochemical Study
Koláčná, Lucie; Čubiňák, M.; Tobrman, T.; Ludvík, Jiří
2024 - anglický
The series of 16 compounds for "organic electronics" comprising the double-bond cyclohexene core extended by pyrene and/or other aromatics were electrochemically characterized by rotating disk voltammetry in N,N-dimethylformamide. Due to multiple substitutions, the resulting potential gap represents the sum of all substituent effects. Different combinations of substituents can be used to achieve the desired properties of cyclohexene-pyrene derivatives. The electrochemical data presented in this contribution facilitate further tuning of properties of these molecules and systems to achieve features required in material chemistry just by means of chemical modification.
Klíčová slova:
pyrene; cyclohexene; conjugation
Plné texty jsou dostupné na vyžádání prostřednictvím repozitáře Akademie věd.
Redox Properties of Pyrene-Cyclohexene Conjugates – Electrochemical Study
The series of 16 compounds for "organic electronics" comprising the double-bond cyclohexene core extended by pyrene and/or other aromatics were electrochemically characterized by rotating disk ...
Electrochemical Valorization of Lignocellulosic Biomass Amination of Furfural and 5-Hydroxymethylfurfural
Donkeng Dazie, Joel; Koláčná, Lucie; Urban, Jiří; Lamač, Martin; Ludvík, Jiří
2024 - anglický
Furfural (FF) and 5-hydroxymethylfurfural (HMF) isolated from waste lignocellulosic biomass represent renewable sources. The present contribution deals with the transformation of FF and HMF into furfuryl amines which are important precursors namely for pharmaceutical synthesis. First, FF and HMF underwent condensation reactions with various amines which were electrochemically monitored to optimize the process. The resulting Schiff bases were identified by NMR and subsequently electrochemically reduced in basic media. The vicinal diamine (aminopinacol) was the main product besides the expected furfuryl amines. This reaction is a contribution to green synthesis because it was performed electrochemically, in water, and without any metallic catalysts.
Klíčová slova:
furfural; 5-hydroxymethylfurfural; (di)amines
Plné texty jsou dostupné na vyžádání prostřednictvím repozitáře Akademie věd.
Electrochemical Valorization of Lignocellulosic Biomass Amination of Furfural and 5-Hydroxymethylfurfural
Furfural (FF) and 5-hydroxymethylfurfural (HMF) isolated from waste lignocellulosic biomass represent renewable sources. The present contribution deals with the transformation of FF and HMF into ...
Electrochemical Properties of Newly Synthesized Selaginpulvilins
Dostálová, L.; Sokolová, Romana; Schwarzová-Pecková, K.; Rýček, L.
2024 - anglický
The electrochemical properties of newly synthesized selaginpulvilin were investigated by cyclic voltammetry and UV-Vis spectroelectrochemistry. The subject of the study were two\nselaginpulvilins differing in the presence of a hydroxyl group in the media of 0.1 mol L-1 tetrabutylammonium hexafluorophosphate as supporting electrolyte in anhydrous acetonitrile. Both\ncompounds provided an oxidative signal in the positive region until +2.0 V.
Klíčová slova:
oxidation; cyclic voltammetry; selaginpulvilins
Plné texty jsou dostupné na vyžádání prostřednictvím repozitáře Akademie věd.
Electrochemical Properties of Newly Synthesized Selaginpulvilins
The electrochemical properties of newly synthesized selaginpulvilin were investigated by cyclic voltammetry and UV-Vis spectroelectrochemistry. The subject of the study were two\nselaginpulvilins ...
3D-printed Electrodes with Nearly Ideal Charge Transfer Characteristics
Vaněčková, Eva; Sebechlebská, Táňa; Kolivoška, Viliam
2024 - anglický
3D printing is an outstanding manufacturing tool for prototyping customized designs at reduced time and costs, having found applications in fields such as medicine or the automotive industry. The development of printable electrically conductive composite materials brought a revolution to electrochemistry, with 3D-printed electrodes being intensively studied from the viewpoint of\nanalytical performance and stability. However, it is often reported that 3D-printed electrodes have poor charge transfer characteristics, typically due to limited exposure of the electrically conductive phase at the composite surface to the surrounding solution. In this work, we devise and apply simple electrochemical activation procedures that lead to a significant improvement of charge transfer characteristics of 3D printed electrodes.
Klíčová slova:
three-dimensional printing; electrochemistry; electrodes
Plné texty jsou dostupné na vyžádání prostřednictvím repozitáře Akademie věd.
3D-printed Electrodes with Nearly Ideal Charge Transfer Characteristics
3D printing is an outstanding manufacturing tool for prototyping customized designs at reduced time and costs, having found applications in fields such as medicine or the automotive industry. The ...
NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.
Vaše náměty a připomínky posílejte na email nusl@techlib.cz
Provozovatel
Zahraniční báze