Ne (67)
Použitá omezení
(3)
Počet nalezených dokumentů:
67
Publikováno od
do
Measurements on KR-D-11B Optimized Subsonic Blade Cascade
Šimurda, David; Hála, Jindřich
2023 - anglický
This report contains results and evaluation of aerodynamic measurements conducted on a subsonic compressor blade cascade.
Klíčová slova:
compressor blade cascade; experiment; subsonic flow; optimized profile
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Measurements on KR-D-11B Optimized Subsonic Blade Cascade
This report contains results and evaluation of aerodynamic measurements conducted on a subsonic compressor blade cascade.
Optical and Pneumatic Measurements on TR-U-11 Cascade
Luxa, Martin; Hála, Jindřich; Šimurda, David
2023 - anglický
The report contains results and evaluation of conducted optical (interferometry and schlieren technique) and pneumatic measurements on the first variant of the new tip section, intended for turbine rotor blade.
Klíčová slova:
transonic flow; rotor turbine blade; tip section
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Optical and Pneumatic Measurements on TR-U-11 Cascade
The report contains results and evaluation of conducted optical (interferometry and schlieren technique) and pneumatic measurements on the first variant of the new tip section, intended for turbine ...
Implementation of a plasticity model with advanced kinematic hardening rule for additively manufactured materials
Marek, René; Parma, Slavomír; Gabriel, Dušan; Džugan, J.
2023 - anglický
This technical report summarizes particularly the modeling part of the project DP 04_01_NPO “Emission-free technologies for local energy sources replacement” including development of models to describe multi-material 3D printed structures. The work is done in cooperation between COMTES FHT, a.s., the Institute of Thermomechanics of the Czech Academy of Sciences, v.v.i. and PROINNO, a.s. The goal of the project is the development of material models describing the behavior of multi-material components deposited by the direct deposition method (DED) under multiaxial cyclic loading.\nIn the report, a plasticity model suitable for materials prepared by the additive manufacturing method is compiled and used. The model uses Hill's plasticity condition, an advanced multi-component kinematic hardening rule, and an isotropic hardening rule. The associated flow rule is chosen and the implementation assumes the theory of small deformations. All constitutive relationships are presented and discussed for the selected model, and the model is thus fully and unambiguously formulated. The model is analytically integrated for a special case of loading and a special choice of parameters of the plasticity condition, namely transverse isotropy. A discretization scheme for numerical integration and procedures for FE implementation of the model are presented. For the FE implementation, a formulation in the displacement field is assumed, specifically the FE solver Abaqus and the implementation of the model using the UMAT interface are targeted. Several examples of the model's response to monotonic, uniaxial and biaxial cyclic loading trajectories are presented. \n Tato zpráva shrnuje postup prací na dílčím projektu DP 04_01_NPO “Emission-free technologies for local energy sources replacement” zahrnující vývoj modelů pro popis chování multi-materiálových 3D tištěných struktur řešený v konsorciu COMTES FHT, a.s., Ústav termomechaniky AV ČR, v.v.i. a PROINNO, a.s. Cílem projektu je vývoj materiálových modelů popisujících chování multi-materiálových komponent deponovaných metodou přímé depozice (DED) pří víceosém cyklickém zatěžování. \nVe zprávě je sestaven a použit model plasticity vhodný pro materiály připravené metodou aditivní výroby. Model využívá Hillovu podmínku plasticity, pokročilý vícesložkový model kinematického zpevnění a model isotropního zpevnění. Je zvolen asociovaný zákon tečení a implementace předpokládá teorii malých deformací. Pro zvolený model jsou uvedeny a diskutovány všechny konstitutivní vztahy a model je tak plně a jednoznačně formulován. Model je analyticky integrován pro speciální případ zatěžování a speciální volbu parametrů podmínky plasticity, konkrétně příčnou isotropii. Je prezentováno diskretizační schema pro numerickou integraci a procedury pro MKP implementaci modelu. U MKP implementace se předpokládá formulace v poli posunutí, konkrétně je pak cíleno na MKP řešič Abaqus a implementaci modelu pomocí rozhraní UMAT. Je prezentováno několik příkladů odezvy modelu na monotónní, jednoosé a víceosé cycklické zatěžovací trajektorie.\n
Klíčová slova:
plasticity; anisotropy; additive manufacturing
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Implementation of a plasticity model with advanced kinematic hardening rule for additively manufactured materials
This technical report summarizes particularly the modeling part of the project DP 04_01_NPO “Emission-free technologies for local energy sources replacement” including development of models to ...
Aerodynamic Measurements on Subsonic Compressor Blade Cascades KR-D-7 and KR-D-8
Šimurda, David; Hála, Jindřich; Luxa, Martin; Radnic, Tomáš
2023 - anglický
This report contains results and evaluation of aerodynamic measurements conducted on two variant subsonic compressor blade cascades with MCA profile (KR-D-7) and DCA profile (KR-D-8) at transonic flow regimes.
Klíčová slova:
compressor blade cascade; experiment; transonic flow; subsonic flow; MCA profile; DCA profile
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Aerodynamic Measurements on Subsonic Compressor Blade Cascades KR-D-7 and KR-D-8
This report contains results and evaluation of aerodynamic measurements conducted on two variant subsonic compressor blade cascades with MCA profile (KR-D-7) and DCA profile (KR-D-8) at transonic flow ...
Aerodynamic Measurements on Transonic Compressor Blade Cascades KR-D-9 and KR-D-10
Šimurda, David; Hála, Jindřich; Luxa, Martin
2023 - anglický
This report contains results and evaluation of aerodynamic measurements conducted on two variant transonic compressor blade cascades with MCA profile (KR-D-10) and DCA profile (KR-D-9) at transonic flow regimes.
Klíčová slova:
compressor blade cascade; experiment; transonic flow; MCA profile; DCA profile
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Aerodynamic Measurements on Transonic Compressor Blade Cascades KR-D-9 and KR-D-10
This report contains results and evaluation of aerodynamic measurements conducted on two variant transonic compressor blade cascades with MCA profile (KR-D-10) and DCA profile (KR-D-9) at transonic ...
Measurements on Turbine Cascade KOBRA
Luxa, Martin; Hála, Jindřich; Šimurda, David
2023 - anglický
The report contains results and evaluation of aerodynamic measurement on a blade cascade representing the section imitating the conical stream line in the last rotor row of a gas trubine under considerable off-design condition. The research report contains detailed specifications of the measured model, overview of the results of the optical measurements (interferometry, schlieren method in Toepler configuration) and pneumatic measurements (traversing with five hole conical probe downstream the cascade).
Klíčová slova:
turbine cascade; turbine off-design condition; tarnsonic flow
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Measurements on Turbine Cascade KOBRA
The report contains results and evaluation of aerodynamic measurement on a blade cascade representing the section imitating the conical stream line in the last rotor row of a gas trubine under ...
Annular impinging jets and an active control of hysteretic effects
Devani, Yogendrasasidhar; Antošová, Zuzana; Trávníček, Zdeněk
2022 - anglický
An annular air jet with and without flow control was studied experimentally using flow visualization and measurements of the wall pressure and flow velocity by the Pitot and Prandtl probes and the hot-wire anemometer. To investigate flow control swirling effects, eight synthetic jets were generated from the annular nozzle center body.The experiments cover Reynolds numbers 4000–10000 (evaluated from the outer exit diameter of the annular nozzle). For Re<9000, the bistability and hysteresis were identified and two different flow field patterns (A and B) were found under the same boundary conditions. For A pattern, a small recirculation area (bubble) of separated flow is attached to the nozzle center body. For B pattern, a large recirculation area of separated flow bridges entire nozzle-to-wall distance. For higher Re > 9000, the bistability and hysteresis were not found.Flow control swirling effects causes suppression of the hysteresis. Moreover, weak flow control causes that the entire annular jet is forced into a precessing motion.
Klíčová slova:
annular jet; impinging jet; bistability; hysteresis
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Annular impinging jets and an active control of hysteretic effects
An annular air jet with and without flow control was studied experimentally using flow visualization and measurements of the wall pressure and flow velocity by the Pitot and Prandtl probes and the ...
Final Report of the Centre of Excellence for Nonlinear Dynamic Behaviour of Advanced Materials in Engineering
Parma, Slavomír; Gabriel, Dušan
2022 - anglický
This final report presents the CeNDYNMAT Center of Excellence, which was established at the Institute of Thermomechanics of the Czech Academy of Sciences in 2016 and ended in 2022. The report summarizes the most important scientific results of the center. It also gives an overview of the main outcomes and developments of the project, including budgeting, purchasing instrumentation, international cooperation and organization of conferences and summer courses.
Klíčová slova:
nonlinear dynamic behavior; advanced materials; metal plasticity
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Final Report of the Centre of Excellence for Nonlinear Dynamic Behaviour of Advanced Materials in Engineering
This final report presents the CeNDYNMAT Center of Excellence, which was established at the Institute of Thermomechanics of the Czech Academy of Sciences in 2016 and ended in 2022. The report ...
Aerodynamic Measurements on Transonic Compressor Blade Cascades KR-D-5 and KR-D-6
Šimurda, David; Hála, Jindřich; Luxa, Martin
2022 - anglický
This report contains results and evaluation of aerodynamic measurements conducted on two variant transonic compressor blade cascades with MCA profile (KR-D-5) and DCA profile (KR-D-6).
Klíčová slova:
compressor blade cascade; experiment; transonic flow; MCA profile; DCA profile
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Aerodynamic Measurements on Transonic Compressor Blade Cascades KR-D-5 and KR-D-6
This report contains results and evaluation of aerodynamic measurements conducted on two variant transonic compressor blade cascades with MCA profile (KR-D-5) and DCA profile (KR-D-6).
Survey of the use of propane as refrigerant R290 in cooling circuits and heat pumps
Aminian, Ali; Prokopová, Olga; Vinš, Václav
2022 - anglický
The technical report presents a review on the application of propane as refrigerant R290 in cooling circuits and heat pumps (HVAC). Safety risks of R290 used in HVAC are addressed according to ANSI/ASHRAE and EN standards. Comparison of thermophysical properties of propane with other refrigerants, solubility and miscibility of propane in compressor oils and heat transfer in condenser and evaporator are discussed. The main aim of the study is to provide an overview about the potential use of propane in the cooling circuit and heat pump for the hydrogen bus developed by the SOR Libchavy company.
Klíčová slova:
cooling circuit; heat pump; hydrogen bus; refrigerant
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Survey of the use of propane as refrigerant R290 in cooling circuits and heat pumps
The technical report presents a review on the application of propane as refrigerant R290 in cooling circuits and heat pumps (HVAC). Safety risks of R290 used in HVAC are addressed according to ...
NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.
Vaše náměty a připomínky posílejte na email nusl@techlib.cz
Provozovatel
Zahraniční báze