Ne (549)
Ano (4)
Počet nalezených dokumentů:
553
Publikováno od
do
PROPERTIES OF NANOCRYSTALLINE FE-NI PARTICLES PREPARED BY THERMAL REDUCTION OF OXALATE PRECURSORS
Švábenská, Eva; Roupcová, Pavla; Havlíček, Lubomír; Schneeweiss, Oldřich
2024 - anglický
Recent technological advancements require development of cost-effective and high-performance magnets \nwhich ideally do not contain rare earth metals or noble metals. The promising candidates are Fe-Ni-based \nalloys, in particular, the Fe50Ni50 L10 phase (tetrataenite), which has a great perspective for producing hard \nmagnetic materials. Our study explores a promising method for preparing nanoparticles of Fe-Ni alloy from an \niron-nickel oxalate precursor. The coprecipitation method was employed to prepare oxalate precursors, \nfollowed by controlled thermal decomposition in a reducing hydrogen atmosphere. The morphology and \nproperties of the resulting particles were analysed using scanning electron microscopy (SEM) coupled with \nenergy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Mössbauer spectroscopy (MS), and \nmagnetic measurements.\nThe SEM analysis revealed that the particles have approximately cube-shaped unit cell morphology with a\nsize in a range of 1 - 2 μm. Upon annealing, the samples contain multiple phases with varying Fe-Ni content.\nMagnetic measurements confirmed the formation of magnetically suitable Fe-Ni phases in the samples after \nannealing. Mössbauer spectroscopy emerged as a highly effective method for characterizing individual phases \nof the Fe-Ni system.
Klíčová slova:
Magnetic materials; thermal decomposition; Mössbauer spectroscopy
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
PROPERTIES OF NANOCRYSTALLINE FE-NI PARTICLES PREPARED BY THERMAL REDUCTION OF OXALATE PRECURSORS
Recent technological advancements require development of cost-effective and high-performance magnets \nwhich ideally do not contain rare earth metals or noble metals. The promising candidates are ...
NANOCERIA PREPARED BY ELECTRON BEAM EVAPORATION
Pizúrová, Naděžda; Hlaváček, A.; Kavčiaková, Zuzana; Roupcová, Pavla; Kuběna, Ivo; Buršík, Jiří; Sokovnin, S. Y.
2022 - anglický
Cerium oxide nanoparticles (nanoceria) are currently one of the most investigated nanomaterials because of their attractive properties used in biomedical applications, catalysis, fuel cells, and many others. These attractive properties are connected with the Ce3+ and Ce4+ valency state ratio. In the nanoparticle form, cerium oxides contain a mixture of Ce3+ and Ce4+ on the nanoparticle surfaces. Switching between these two states requires oxygen vacancies. Therefore, nanoceria's inherent ability to act as an antioxidant in an environmentally-dependent manner and a “redox switch” to confer auto-regenerating capabilities by automatically shifting between Ce4+ and Ce3+ oxidation states is significantly affected by surface morphology. Regarding this demanded behavior, we aimed to characterize synthesized nanoparticle surface quality and its influence on the cerium oxidation states. The received results were used to evaluate the synthesis method's suitability for suggested utilization. We used nanoparticles prepared by electron beam evaporation. This unique physical method includes nanoparticle creation through the fast cooling process followed by breaking radiation damaging nanoparticle surfaces to create surface off-stoichiometry. We prepared a sample containing clusters of a mixture of ultra-small nanoparticles and approximately 100 nm particles. X-ray diffraction confirmed the CeO2 phase in both components. To extract the finest component, we used centrifugal size fractionation. We received 200 nm clusters of 2-10 nm nanoparticles. Nanoparticle shapes and facet types were analyzed using transmission electron microscopy methods. We found out most nanoparticles were formed with truncated octahedrons containing {1,1,1} and {1,0,0} facet types and truncated cuboctahedrons containing {1,1,1}, {1,0,0}, and additional {1,1,0} facets. No octahedron (without truncation) containing only {1,1,1} facets was observed. Nanoparticle shapes containing {1,1,0} and {1,0,0} are suitable for redox activity. Some amount of irregular shapes, beneficial for redox activity, was also observed. Spectroscopy methods confirmed Ce3+ content.
Klíčová slova:
Ce3+ and Ce4+; electron beam evaporation; facet types; hrtem; Nanoceria
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
NANOCERIA PREPARED BY ELECTRON BEAM EVAPORATION
Cerium oxide nanoparticles (nanoceria) are currently one of the most investigated nanomaterials because of their attractive properties used in biomedical applications, catalysis, fuel cells, and many ...
INFLUENCE OF THE DEPOSITION PARAMETERS ON MICROSTRUCTURE AND PROPERTIES OF HVOF SPRAYED WC-CRC-NI COATING
Vražina, Tomáš; Šulák, Ivo; Poloprudský, Jakub; Zábranský, K.; Gejdoš, P.; Hadraba, Hynek; Čelko, L.
2022 - anglický
This paper investigates the influence of thermal spray parameters of the high-velocity oxygen fuel (HVOF) process on the properties of cermet coatings prepared from commercially available Amperit 551 WC-CrC-Ni powder. Three different processing parameters were applied to optimize the production process with the aim to achieve preeminent mechanical properties and fully dense material without microstructural defects. The deposition was carried out by a GLC5 gun. The velocity and temperature of powder particles in the spray stream were monitored by Accuraspray Tecnar diagnostic tool. The quality of deposited coatings was analyzed by means of light microscopy, scanning electron microscopy, and X-ray diffraction. The chemical composition of the used powder and sprayed WC-CrC-Ni coating was determined by energy dispersive spectroscopy. It was found that the spray parameters have a negligible effect on the resulting microstructure and phase composition of the coating. However, the porosity and surface roughness were significantly affected by the variation in process parameters. To assess the basic mechanical properties of HVOF sprayed coating instrumented Vickers hardness measurements were utilized. The coating hardness reached mean values over 1400 HV 0.1 and the indentation modulus varied from 152-279 GPa.
Klíčová slova:
hvof; microhardness; WC-CrC-Ni
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
INFLUENCE OF THE DEPOSITION PARAMETERS ON MICROSTRUCTURE AND PROPERTIES OF HVOF SPRAYED WC-CRC-NI COATING
This paper investigates the influence of thermal spray parameters of the high-velocity oxygen fuel (HVOF) process on the properties of cermet coatings prepared from commercially available Amperit 551 ...
Inverse-Heusler Mn2FeSi alloy prepared by powder metallurgy route
Životský, O.; Skotnicová, K.; Čegan, T.; Juřica, J.; Gembalová, L.; Zažímal, František; Jirásková, Yvonna; Szurman, I.
2022 - anglický
The Mn2FeSi inverse-Heusler alloy was prepared by solid-state reactions using ball milling for 168 h in n hexane. Two milling procedures varying in the ball-to-powder ratio, namely 4:1 and 10:1, were used to follow \ntheir influence on alloy formation and its physical properties. In both cases no Heusler structure was obtained \ndirectly and therefore the subsequent annealing at 1223 K for 1.5 h in pure Ar was applied. The energy dispersive X-ray analysis resulted in the chemical composition about 49.0-49.9 at% Mn, 25.3-25.6 at% Fe, and \n24.8-25.4 at% Si, in a good agreement with nominal one. X-ray diffraction of both powders confirmed inverse Heusler XA structure of lattice parameters 0.5675 nm (4:1) and 0.5677 nm (10:1), only slightly higher as \ntheoretically obtained 0.560 nm. The presence of minor oxidation phases was also observed in the particle \nstructure of powders. Magnetic properties were analysed at low and room temperatures. Both alloys exhibit \nparamagnetic behaviour at room temperature confirmed by transmission Mössbauer spectroscopy \nmeasurements. Different magnetic behaviour of alloys is observed below 65 K.
Klíčová slova:
Heusler alloy, powder, ball milling, microstructure, magnetism; powder; ball milling; microstructure; magnetism
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Inverse-Heusler Mn2FeSi alloy prepared by powder metallurgy route
The Mn2FeSi inverse-Heusler alloy was prepared by solid-state reactions using ball milling for 168 h in n hexane. Two milling procedures varying in the ball-to-powder ratio, namely 4:1 and 10:1, were ...
Nanoparticels from brake pads wear
Švábenská, Eva; Roupcová, Pavla; Friák, Martin; Schneeweiss, Oldřich
2022 - anglický
Exposure to particulate air pollution has been associated with a variety of health problems. One of the main\nsources of metal-rich airborne particulate pollution in roadside environments are brake-wear emissions. The \nscanning electron microscopy (SEM) and transmission electron microscopy (TEM), Mössbauer spectroscopy \n(MS), X-ray powder diffraction (XRD) was used to a make quantitative evaluation of wear particles in two \nsamples. Sizes, morphologies, oxidation state, and trace element compositions of wear particles were\ninvestigated using combination of several methods revealed high concentrations of Fe species and phases, \noften associated with carbonaceous material. SEM and TEM observations show that brake wear particles with \na size of tens to hundreds of nm mainly form particle agglomerates. However, ultrafine (<100 nm) particles are \nlikely to pose a health threat after inhalation and/or ingestion.
Klíčová slova:
Wear particles; analysis; TEM; iron oxides; metallic particles
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Nanoparticels from brake pads wear
Exposure to particulate air pollution has been associated with a variety of health problems. One of the main\nsources of metal-rich airborne particulate pollution in roadside environments are ...
Advanced statistical evaluation of fatigue data obtained during the measurement of concrete mixtures with various water-cement ratio
Seitl, Stanislav; Benešová, A.; Blasón, S.; Miarka, Petr; Klusák, Jan; Bílek, V.
2022 - anglický
The Basquin’s law is usually applied for the evaluation of fatigue properties of civil engineering \nmaterials. For materials like concrete, some researchers recommended applying the Weibull model. In this\ncontribution, Basquin’s law, Castillo-Canteli model and Kohout-Věchet model were applied for the advanced \nstatistical description of S−N curves (Wöhler curve). For the application of the models, the experimental data \nmeasured on reference concrete mixtures used for the development of self-healing concrete at the Faculty of \nCivil Engineering, TU Ostrava. Fitting data of applied models were compared and analyzed
Klíčová slova:
Concrete, fatigue; fatigue; S-N curve; Kohout-Věchet model; Castillo-Canteli model; Basquin model
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Advanced statistical evaluation of fatigue data obtained during the measurement of concrete mixtures with various water-cement ratio
The Basquin’s law is usually applied for the evaluation of fatigue properties of civil engineering \nmaterials. For materials like concrete, some researchers recommended applying the Weibull model. In ...
Structural and magnetic properties of Fe-oxide layers prepared by inkjet printing on Si-substrate
Zažímal, František; Svoboda, T.; Dzik, P.; Homola, T.; Jirásková, Yvonna
2021 - anglický
Magnetic films with two, four, six, and eight layers were prepared using 2D inkjet printing on the 333 K heated Si-substrates at ambient conditions. The microstructure, phase composition of layers, and magnetic studies were investigated using wide spectrum of experimental methods with the aim to find the optimal conditions for producing magnetic sensors by digital printing technology in the near future. As the magnetic compound, the hematite powder was chosen and its milling with Si-binder dissolved in dowanol using glass balls and vial to prevent contamination was done to prepared suspension appropriate for printing. It is shown that hematite transformed markedly into maghemite, thus the layers consisted of small amount hematite and dominant maghemite phases determining the magnetic properties. From the viewpoint of magnetic behavior, the highest saturation magnetization and the lowest coercivity was obtained at the sample with 8 layers.
Klíčová slova:
Inkjet printing; hematite; physical properties; testing methods
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Structural and magnetic properties of Fe-oxide layers prepared by inkjet printing on Si-substrate
Magnetic films with two, four, six, and eight layers were prepared using 2D inkjet printing on the 333 K heated Si-substrates at ambient conditions. The microstructure, phase composition of layers, ...
Influence of severe plastic deformation and subsequent annealing on creep behaviour of martensitic 9% Cr steel
Král, Petr; Dvořák, Jiří; Sklenička, Václav; Horita, Z.; Tokizawa, Y.; Tang, Y.; Kunčická, Lenka; Kuchařová, Květa; Kvapilová, Marie; Svobodová, M.
2021 - anglický
The objective of the study is to evaluate the effects of severe plastic deformation (SPD) and annealing on creep behaviour of advanced tungsten modified creep-resistant 9 % Cr martensitic P92 steel. The as-received P92 steel was deformed by high-pressure torsion (HTP), high-pressure sliding (HPS) and rotary swaging (RS) at room temperature prior creep testing. These SPD methods imposed significantly different equivalent plastic strain in the range from 1 up to 20. Constant load creep tests in tension were performed in an argon atmosphere at 873 K and applied stress ranging from 50 to 200 MPa. The microstructure and phase composition of P92 steel were studied using a scanning electron microscope Tescan Lyra 3 and a transmission electron microscope Jeol 2100F. The results show that under the same creep loading conditions the HPT and HPS-processed P92 steel exhibited significantly faster minimum creep rates, creep fracture strain and the decrease in the value of the stress exponent of the creep rate in comparison with as-received P92 steel. However, it was revealed that the RS-processed specimens exhibited one order of magnitude lower minimum creep rate and lower ductility compared to commercial P92 steel. The creep curves for the HPT and HPS-processed states exhibited a pronounced minimum of strain rate. The pronounced minimum of strain rate disappeared when these states were annealed at 923K/500h before application of creep loading. The microstructure changes occurring during creep and different creep behaviour between as-received and deformed states are discussed.
Klíčová slova:
Creep-resistant 9 %Cr steels; severe plastic deformation; creep; microstructure
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
Influence of severe plastic deformation and subsequent annealing on creep behaviour of martensitic 9% Cr steel
The objective of the study is to evaluate the effects of severe plastic deformation (SPD) and annealing on creep behaviour of advanced tungsten modified creep-resistant 9 % Cr martensitic P92 steel. ...
AB INITIO STUDY OF SILVER NANOPARTICLES, GRAIN BOUNDARIES AND THEIR \nQUADRUPLE JUNCTIONS
Polsterová, S.; Všianská, Monika; Friák, Martin; Pizúrová, Naděžda; Sokovnin, S.; Šob, Mojmír
2021 - anglický
Motivated by our experimental research related to silver nanoparticles with various morphologies, we have employed quantum-mechanical calculations to provide our experiments with theoretical insight. We have computed properties of a 181-atom decahedral silver nanoparticle and two types of internal extended defects, -5(210) grain boundaries (GBs) and quadruple junctions (QJs) of these GBs. We have employed a supercell approach with periodic boundary conditions. Regarding the thermodynamic stability of the decahedral nanoparticle, its energy is higher than that of a defect-free face-centered cubic (fcc) Ag by 0.34 eV/atom. As far as the -5(210) GB is concerned, its energy amounts to 0.7 J/m2 and we predict that the studied GBs would locally expand the volume of the lattice. Importantly, the system with GBs is found rather close to the limit of mechanical stability. In particular, the computed value of the shear-related elastic constant C66 is as low as 9.4 GPa with the zero/negative value representing a mechanically unstable system. We thus predict that the -5(210) GBs may be prone to failure due to specific shearing deformation modes. The studied GBs have also the value of Poisson’s ratio for some loading directions close to zero. Next, we compare our results related solely to -5(210) GBs with those of a system where multiple intersecting -5(210) GBs form a network of quadruple junctions. The value of the critical elastic constant C66 is higher in this case, 13 GPa, and the mechanical stability is, therefore, better in the system with QJs.
Klíčová slova:
Elasticity; Grain boundaries; Junctions; Nanoparticles
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
AB INITIO STUDY OF SILVER NANOPARTICLES, GRAIN BOUNDARIES AND THEIR \nQUADRUPLE JUNCTIONS
Motivated by our experimental research related to silver nanoparticles with various morphologies, we have employed quantum-mechanical calculations to provide our experiments with theoretical insight. ...
MULTI-PARAMETER MTS AND SED CRITERION APPLIED ON A CRACK IN AN ALKALI-ACTIVATED CONCRETE SPECIMEN UNDER MIXED-MODE LOADING
Malíková, Lucie; Miarka, Petr; Simonová, H.
2020 - anglický
The paper is devoted to an analysis of a crack propagation in a semi-circular concrete specimen under three-point bending. I+II mixed-mode loading is ensured via an inclined crack. Crack deflection angle is investigated by means of the generalized/multi-parameter form of the Maximum Tangential Stress (MTS) criterion and Strain Energy Density (SED) criterion as well as experimentally. The multi-parameter fracture mechanics concept applied in this work is based on the approximation of the crack-tip stress field by means of the Williams series expansion (WE). It has been proved that this approach can help to describe crack behavior in some kinds of materials better than the classical (one-parameter: stress intensity factor) fracture mechanics. This conclusion is discussed also in this paper.
Klíčová slova:
t-stress; fracture; field; Multi-parameter fracture mechanics; Alkali-activated concrete; Mixed-mode loading; mts; sed
Plné texty jsou dostupné na jednotlivých ústavech Akademie věd ČR.
MULTI-PARAMETER MTS AND SED CRITERION APPLIED ON A CRACK IN AN ALKALI-ACTIVATED CONCRETE SPECIMEN UNDER MIXED-MODE LOADING
The paper is devoted to an analysis of a crack propagation in a semi-circular concrete specimen under three-point bending. I+II mixed-mode loading is ensured via an inclined crack. Crack deflection ...
NUŠL poskytuje centrální přístup k informacím o šedé literatuře vznikající v ČR v oblastech vědy, výzkumu a vzdělávání. Více informací o šedé literatuře a NUŠL najdete na webu služby.
Vaše náměty a připomínky posílejte na email nusl@techlib.cz
Provozovatel
Zahraniční báze